Citizen Systems CBM-270 user manual ESC \ n1 n2, Esc $

Page 68

CBM-270 User’s Manual

ESC \ n1 n2

[Function]

Specifying the relative positions

[Code]

<1B> H <5C> H <n1> <n2>

[Range]

0 n1 255

 

0 n2 255

[Outline]

The printing start position is specified in the number of dots(1/203 inch unit) from the current

 

position.

 

Rightward direction is taken as plus and leftward direction as minus._

 

To specify N dot in minus (left) direction, use a complement of N for assignment.

 

N dots = 65536 N

 

The number of dots is divided by 256, whose quotient is taken as n2 and the residual as

 

n1.

 

[Caution]

Specifying exceeding the top of line or the end of line is ignored.

[Default]

The initial value is not specified.

[See Also]

ESC $

 

[Sample Program]

[Print Results]

 

See Sample Program and Print Results for ESC $ on Page 67.

Image 68
Contents Citizen LVD EMCWichtige Sicherheitsanweisungen Lärmemission kleiner 70dBA Sicherheitshinweis CBM-270 User’s Manual Safety Precautions Be Sure to Observe CBM-270 User’s Manual Precautions for Installation Precautions for Handling Daily Maintenance Contents German Appendix113 Basic Specifications FeaturesOutline UnpackingBasic Specifications EMI Printing Position Paper SpecificationsRecommended Paper Head and Paper Cutter Layout Outer Appearance and Component Parts Connecting AC Adapter OperationCBM-270 User’s Manual Connecting Interface Cable Inserting the Paper How to Remove Remaining Paper Roll Eliminating the Paper Jam Feed Switch Function When Thermal Paper is UsedWhen Label Paper is Used When the Macro is ExecutedPaper Near End Function OFFAuto-Loading Function Self-Print FunctionOperation Panel and Display of Error Error Details12 Red/Black Print Precautions for Use OFFCBM-270 User’s Manual DIP Switch Setting Location of DIP SwitchDIP Switch Function Jumper Wire FunctionUSA Parallel Interface SpecificationsConnectors Pin Configuration Electrical Characteristics Input and Output SignalsInput and Output Signals Timing Chart Data Receiving Control BufferingSerial Interface RXDDTR DSRData Configuration Error Detection Output TXD, DTR Printer Side Host SidePower Connector Maintenance and Service Command List Print Control FunctionsCommand Details Descriptions of Each ItemXxxx Command Details CBM-270 User’s Manual ESC SP n ESC ! n ESC % n ESC & s n m a p s×a m−n+1 ESC * m n1 n2 d k Print Results Dots single density Dots double density ESC − n ESC 3 nESC = n ESC D n k NUL ESC E nESC !, ESC G ESC G nESC J n See Sample Program and Print Results for ESC 2 on ESC R n Default Sample Program ESC V nESC a n ESC c 3 n Parallel Interface Only ESC c 4 nESC c 5 n ESC d nESC n n ESC t nESC Serial Interface Only Fixed to Not defined Sample ProgramESC n ESC $ n1 n2 ESC \ n1 n2 GS k n d k NUL UPC-A UPC-E JAN13 EAN JAN 8 EAN CodeCodabar NW-7 UPC-AJAN-8EAN CODE39ITF CodabarTest Code Btestcode A123UPC-E GS w n GS h nDefault See Also GS f Sample Program Print Results GS f n GS * n1 n2 d n1 × n2 × GS / mVertical Direction Horizontal Direction Normal mode CBM-270 User’s Manual GS n1 n2 n3 DC3 n Only When Label Printer is SelectedDC2 a n GS FF GS FF, GSGS C0 m n GS C1 n1 n2 n3 n4 n5 n6 GS C2 n1 n2 GS C N1 N2 N3 N4 N5GS c GS a m n Only When Label Printer is Selected Character Codes TableInternational Domestic International Character Codes Table Appendix 1. Block Diagram Appendix 2. Outline Drawing Appendix 3. Wall Mounting Holes Layout Drawing German VorsichtPage ZU Beachtende Sicherheitsmassregeln Warnung VorsichtWarnung Vorsichtsmassregeln FÜR DIE Aufstellung Vorsichtsmassregeln FÜR DIE Handhabung Tägliche Wartung VorsichtBetrieb Anschließen des NetzteilsAnschließen des Schnittstellenkabels Einsetzen des Papiers Entnehmen der eingesetzten Papierrolle Beseitigen von Papierstau FEED-Schalterfunktion Papierende-FunktionBei Verwendung von Thermalpapier Bei Verwendung von EtikettenpapierBusy DTR/FAULT Paper Papiermangel-FunktionAutoladefunktion SelbstdruckfunktionBedienfeld und Fehleranzeigen 12 Rot/Schwarz-Druck Vorsichtsmaßregeln Fehler-EinzelheitenVorsicht DIP-SCHALTEREINSTELLUNG Lage der DIP-SchalterDIP-Schalterfunktion Jumperdraht-FunktionItalien Japan Wartung UND Dienst