Citizen Systems CLP-6002, CLP-6001 user manual EMI Compliance Statement For Canadian Users

Page 3

EMI COMPLIANCE STATEMENT

FOR CANADIAN USERS

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Use shielded cables to connect this device to computers.

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

ETAT DE CONFORMITE EMI A L'USAGE

DES UTILISATEURS CANADIENS

Cet équipment produit et utilise l'énergie à radiofréquences et s'il n'est pas installé et utilisé correctment, c'esst à dire en accord strict avec les instructions du fabricant, il risque de provoquer des intérferences avec la réception de la radio et de la télévision.

Le présent appareil numérique n'émet pas de bruite radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Cet équipment est conçu pour fournir une protection satisfaisante contre de telles interférences dans une installation résidentielle. Cependant, il n'y a pas de garantie contre les interférences avec les réceptions radio ou télévison, provoquées par la mise en et hors circuit de l'équipment; aussi, il est demandé a l'utilisateur d'essayer de corriger l'interférence par l'une ou plus des mesures suivantes:

Réorienter l'antenne de réception.

Installer l'ordinateur autre part, par égard pour le récepteur.

Brancher l'ordinateur dans une prise de courant différente de façon à ce que l'ordinateur et le récepteur soient branchés sur des circuits différents.

- ii -

Image 3
Contents CLP-6001/6002 FCC Compliance Statement For American Users EMI Compliance Statement For Canadian Users Important Safety Instructions Page Safety Signs Page General Precautions Precautions When Installing the Printer Chapters in This Manual Table of Contents Chapter Troubleshooting Xii Chapter Setup Confirmation of Carton Contents Front View Part Names and FunctionsInside View Names and functions of each part Side View Connection to Power Connection to a Computer Chapter Control Panel Control Panel Normal Operating Mode LCD/LED Indications and Adjustment ControlsSelf-Test Mode Printer Setup ModeMode item Indication Default values System Maintenance ModeVoltage setting mode Chapter Paper and Ribbon Kinds of Paper Specification of Label and TagPaper specification Units for position and length Reference line and points Ribbon Paper Setting Roll paper Reference side Notch for alignment Ribbon Setting Print Head Offset Adjustments Print head position for label Upper frame window Head pressure adjust-screw Ribbon width Ribbon winding Ribbon feed Tension Section Ribbon Tension AdjustmentsExterior view and part names Paper Detector Adjustments for CLP-6001 onlyHow to operate adjustable sensor Page Troubleshooting Error descriptions and indications Error MessagesCmnd Error indications and corrective actions Page − − Power Troubleshooting Paper Feed Troubleshooting Ribbon Feed Troubleshooting Print Troubleshooting Interface Troubleshooting Page Chapter Options Auto-Cutter Unit Peeler Unit Adjustable SensorPcmcia Memory Card Page Chapter Specifications Postnet Main SpecificationsPage LCD Description Interface System configurationSerial interface Specification of interfaceFig. Loopback test 3 RS-232C loopback testFig. Buffer in use 4 RS-232C protocolPage Interface pin assignment Parallel interface pin assignment table STX + L With print Without print Outline of Command SystemExample of Connection to a Computer Tear-off when printing Tear-Off FunctionTurning Tear ON/OFF Paper is fed to the tear position Tear-off when feedingTear-off and type of data Cut position adjustmentsWhen fnnn command is executed while tear-off is OFF Priority order