Delta Tau 4Ax-602804-xHxx manual Contents

Page 3

MACRO-CPU Hardware Reference

CONTENTS
INTRODUCTION	1
3U Product Configurations (General Description)	2
MACRO CPU Specifications	4
Physical Specifications	4
Electrical Specifications	4
3U MACRO-CPU CONFIGURATION	5
3U MACRO CPU BOARD HARDWARE SETUP	7
3U MACRO CPU Board Jumper & Switch Setup	7
MACRO CPU Board Connections	8
3U MACRO-CPU JUMPER AND SWITCH CONFIGURATIONS	11
3U MACRO-CPU Card Layout	11
E1: Watchdog Timer Disable	12
E2: CPU Mode Operation	12
E3: Serial Port Baud Rate	12
E4: Power Supply-Loss Control (±15Vdc Supply Monitor)	12
E5: MACRO Received Signal Detect/Bypass Mode (rev -105 and 106 only). Does not exist on rev 107 and later models.
...............................................................................................................................................................................................	13
E40: MACRO Input (Fiber/Wired) Selector	13
JP3: MACRO Loop back Test Select For Copper Only (rev -104 and earlier)	13
JP4: Reserved for Future Use	13
JP5-JP6: MACRO Copper EQ Select (rev -104 and earlier)	14
Switch Configurations	15
SW1: MACRO Slave Node Configure	15
SW2: MACRO Master Number Select	15
Connector Summary	16
MACRO STATION CHARACTER DISPLAY	17
HARDWARE RE-INITIALIZATION	18
FIRMWARE UPDATES	20
3U MACRO-CPU BOARD CONNECTOR PIN-OUTS	22
J6: (JTHW) Multiplexer Port Connector	22
J7: (JRS232) Serial Port Connector	24
J14, J17: MACRO COPPER I/O (OPT C)	25
P1: UBUS Interface Connector	26
TB1: (JPWR) 4-Pin Terminal Block	27
U73: MACRO Fiber Optic Connector (OPT A)	27

Contents

i

Image 3

Contents Macro CPU Board Page Contents MACRO-CPU Hardware Memory MAP 3U Macro CPU IntroductionUmac Macro Station Configuration Axis Stack Configuration 3U Product Configurations General DescriptionUmac Macro Umac and 3U-Stack Products Umac ProductsMacro CPU Specifications Physical SpecificationsElectrical Specifications 3U MACRO-CPU Configuration MACRO-CPU Hardware Reference 3U MACRO-CPU Configuration 3U Macro CPU Board Hardware Setup 3U Macro CPU Board Jumper & Switch SetupWhich Stack Axis Backplane Umac Axis SW1 Setting Macro CPU Board Connections MACRO-CPU Hardware Reference Page 3U MACRO-CPU Card Layout 3U MACRO-CPU Jumper and Switch ConfigurationsE3 Serial Port Baud Rate E1 Watchdog Timer DisableE2 CPU Mode Operation E4 Power Supply-Loss Control ±15Vdc Supply MonitorThis jumper does not exist on MACRO-CPU versions Greater E40 Macro Input Fiber/Wired SelectorJP4 Reserved for Future Use This jumper does not exist on MACRO-CPU versions EarlierJP5-JP6 Macro Copper EQ Select rev -104 and earlier Switch Configurations SW1 Macro Slave Node ConfigureSW2 Macro Master Number Select U73 Connector SummaryJ14, J17 TB1Macro Station Character Display Hardware RE-INITIALIZATION MACRO-CPU Hardware Reference Hardware Re-initialization Make sure to power down the Macro Station Firmware UpdatesMACRO-CPU Hardware Reference Firmware Updates Front View 3U MACRO-CPU Board Connector PIN-OUTSJ6 Jthw Multiplexer Port Connector Pin # SymbolCircuitry For J6- Jthw Interface J7 JRS232 Serial Port Connector Pin RJ45 Front View Pin # Symbol Function Description DATA+Data P1 Ubus Interface Connector U73 Macro Fiber Optic Connector OPT a Location B-4 Pin # Symbol Function DescriptionTB1 Jpwr 4-Pin Terminal Block Reference Addr hex Description MACRO-CPU Hardware Memory MAPMACRO-CPU Hardware Reference MACRO-CPU Hardware Memory Map Accessories ACC-55E, UnetACC-53E, SSI Amplifiers Analog