Delta Tau 4Ax-602804-xHxx manual MACRO-CPU Hardware Memory MAP, Reference Addr hex Description

Page 32

MACRO-CPU Hardware Reference

U MACRO-CPU HARDWARE MEMORY MAP

The values in this table represent the hardware locations associated with register-based transactions that occur in the 3U MACRO-CPU.

Reference

ADDR (hex)

Description

CS00-

$FFC0

Stack I/O select #1

CS02-

$FFC8

Stack I/O select #2

CS04-

$FFD0

Stack I/O select #3

CS06-

$FFD8

Stack I/O select #4

CS0-

$C000

Stack axis 1-4 select

CS1-

$C020

Stack axis 5-8 select

CS2-

$C040

UBUS backplane axis 1-8 select

CS3-

$C060

UBUS backplane axis 5-8 select

CS4-

$C080

On-board DSPGATE2 select

CS4X-

$C0C0

UBUS backplane MACROgate or DSPgate2 select (CS4- on UBUS)

CS10-

$FFE0

UBUS backplane I/O select #1

CS12-

$FFE8

UBUS backplane I/O select #2

CS14-

$FFF0

UBUS backplane I/O select #3

CS16-

$FFF8

UBUS backplane I/O select #4

MEMCS0-

$D000

UBUS hardware I/O field (was DPRCS-)

MEMCS1-

$E000

UBUS hardware I/O field (was VMECS-)

 

 

 

The addressing field size is 16-bits in the 3U MACRO-CPU. The address table above is similar to the PMAC2 product line.

28

U MACRO-CPU Hardware Memory Map

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Macro CPU Board Page Contents MACRO-CPU Hardware Memory MAP Introduction 3U Macro CPU3U Product Configurations General Description Umac Macro Station Configuration Axis Stack ConfigurationUmac and 3U-Stack Products Umac Products Umac MacroElectrical Specifications Macro CPU SpecificationsPhysical Specifications 3U MACRO-CPU Configuration MACRO-CPU Hardware Reference 3U MACRO-CPU Configuration Which Stack Axis Backplane Umac Axis SW1 Setting 3U Macro CPU Board Hardware Setup3U Macro CPU Board Jumper & Switch Setup Macro CPU Board Connections MACRO-CPU Hardware Reference Page 3U MACRO-CPU Jumper and Switch Configurations 3U MACRO-CPU Card LayoutE1 Watchdog Timer Disable E2 CPU Mode OperationE4 Power Supply-Loss Control ±15Vdc Supply Monitor E3 Serial Port Baud RateE40 Macro Input Fiber/Wired Selector JP4 Reserved for Future UseThis jumper does not exist on MACRO-CPU versions Earlier This jumper does not exist on MACRO-CPU versions GreaterJP5-JP6 Macro Copper EQ Select rev -104 and earlier SW2 Macro Master Number Select Switch ConfigurationsSW1 Macro Slave Node Configure Connector Summary J14, J17TB1 U73Macro Station Character Display Hardware RE-INITIALIZATION MACRO-CPU Hardware Reference Hardware Re-initialization Firmware Updates Make sure to power down the Macro StationMACRO-CPU Hardware Reference Firmware Updates 3U MACRO-CPU Board Connector PIN-OUTS J6 Jthw Multiplexer Port ConnectorPin # Symbol Front ViewCircuitry For J6- Jthw Interface J7 JRS232 Serial Port Connector Data Pin RJ45 Front View Pin # Symbol Function DescriptionDATA+ P1 Ubus Interface Connector TB1 Jpwr 4-Pin Terminal Block U73 Macro Fiber Optic Connector OPT aLocation B-4 Pin # Symbol Function Description MACRO-CPU Hardware Memory MAP Reference Addr hex DescriptionMACRO-CPU Hardware Reference MACRO-CPU Hardware Memory Map ACC-53E, SSI AccessoriesACC-55E, Unet Amplifiers Analog
Top Page Image Contents