Microtest TSB-67 - 568A Annex E manual Appendix C Cable Pin-outs, Press Save F1

Page 58

4.Use the arrow keys and the Unsel/Sel (F2) key so that the only pairs selected (marked with a x) are 36 and 45.

5.Press Save (F1).

6.Select Limits.

7.Select Impedance. Change the Minimum limit from 80 to 135. Change the Maximum limit from 125 to 165. Press Save (F1) to save the new limits.

8.Press the ESCAPE key twice.

9.Press Default (F1) to select “*Cat 5 Link” as the default Autotest. The “*” indicates that this is a user-defined Autotest.

10.If the length of cable that you are testing is near 328 feet, you may need to change the maximum Length limit from 328 to 361 feet. Other limits such as the Loop Resistance and Capacitance may also need to be changed proportionately to the increase in Length limit if these tests are failing marginally.

11.You are now ready to press the AUTOTEST key to run the Token Ring Cat 5 Autotest.

Appendix C: Cable Pin-outs

Cable Pin-outs

B-9 Female DB-9 Male

1___________1

2___________2

3___________3

4___________4

5___________5

6___________6

7___________7

8___________8

9___________9

Serial Cable DB-9 Female to DB-9 Male Pin-outs

B-9 Female DB-25 Male

1___________8

2___________3

3___________2

4___________20

5___________7

6___________6

7___________4

8___________5

9___________22

Serial Cable DB-9 Female to DB-25 Male Pin-outs

Image 58

Contents N t a S c a n n e r O d u c t F a m i l y E r G u i d e Introduction Getting Started Charging the Scanner’s BatteryNi-Cd Battery Scanner and 2-Way Injectors Ready ScreenBattery Refresh Mode Way Injector+/2-Way Injector BatteryNi-Cd Battery Tips PentaScanner+ is in battery refresh modeSuper Injector+/Super Injector Battery Test ConnectorsPass Way Injector+/2-Way Injector LED IndicatorsHigh Voltage Protection FailCharging Super Injector+/Super Injector LED IndicatorsWhen to Use the Injector CircuitUsing Multiple Injectors Injector CalibrationCalibration Connections Mod 8 Adapter NotePress the Extended Functions key Connections Basic Link with Modular 8 Jacks Basic Link with IDC Block and Modular 8 JackFull Channel Modular 8 Link Autotest Selecting the Cable Type Steps for Running AutotestExtended Functions key and select Calibrate Injector Editing the Cable Type Calculating NVPEditing Autotest Information Customizing AutotestEditing the Autotest Name Selecting Pairs for Autotest Selecting Tests to Run During AutotestRunning Autotest Editing Test LimitsAutotest Results Screen Wire Map Test Results Wire MapViewing Autotest Results Customizing Length Limits LengthLength Test Results Near End Crosstalk Next Propagation Delay Customizing Delay LimitsPropagation Delay Test Results Measuring Next at Both Ends of the LinkCustomizing Next Limits Next Test ResultsNext Graph Next DetailAttenuation Attenuation Limits and Frequency Customizing Attenuation LimitsEditing Attenuation Limits Attenuation Graph Attenuation Test ResultsAttenuation Detail Attenuation-to-Crosstalk Ratio ACRImpedance Customizing ACR LimitsACR Test Results ISO Class DImpedance Test Results Customizing Impedance LimitsLoop Resistance Capacitance Customizing Loop Resistance LimitsLoop Resistance Test Results Customizing Capacitance LimitsCapacitance Test Results Saving Autotest ResultsPrinting Autotest Results Save Sweep DataViewing Autotest Results Summary Sample Autotest Report Editing with the Alphanumeric Keypad Editing, Printing & UpdatingEditing with the Arrow Keys Printing or Downloading Test Results Memory, then press Print F3Printing Tips Uploading Autotest Reports to Windows TerminalProcomm Plus for Windows Troubleshooting Printing Problems Problem My printout is garbled. Why?Downloading Software Updates Updating Scanner Software from the PCWaiting for Reflash Updating the 2-Way Injector+/2-Way InjectorOne or more stored Autotest results have been lost Penta -C1 Technical SupportWorld Wide Web Download of Flash image file completeMicrotest Bulletin Board System BBS Find Cable FaultsFaxFacts Short at the Injector End Wire Map for Both Ends of the LinkCross Wiring Short at the Scanner EndMeasure Cable Performance Graph F1Attenuation Limits Next SweepAttenuation Length/Delay NoiseImpulse Noise Peak-to-Peak Noise Analyze LAN TrafficLAN Traffic Display Extended Functions Menu Setting Up the Traffic MonitorExtended Functions Autotest MemoryAutotest Setup Calibrating the InjectorSetting Up Units Setting Up User PreferencesSetting Backlight and Auto Shutoff Times Editing Owner/Company NameSetting the Date and Time Setting Up the Printer PortSelecting a Graphics Printer Tracing a Cable Appendix a SpecificationsDisplaying Injector Information Locating an Office Cable DropEnvironmental Wire MapUser Interface Measurement PortsNear-End Crosstalk Next LengthAttenuation Capacitance ImpedanceLoop Resistance Impulse NoiseHigh Voltage Input/Protection Rechargeable BatteryPower Control LED DisplaysSuper Injector+/Super Injector Physical Characteristics Way Injector+ Next Measurement Performance SpecificationsFeatures Creating a Cat 5 Test for Token Ring Appendix B 150 ohm CablesWorking with 150 Ohm Cables EnvironmentPress Save F1 Appendix C Cable Pin-outsCable Pin-outs Serial Cable DB-9 Female to DB-9 Male Pin-outsAppendix D Working with Coaxial Cable Length/Delay Test Results Impulse Noise Test Results Peak-to-Peak Noise Test Results