Microtest TSB-67 - 568A Annex E manual Impulse Noise Test Results, Peak-to-Peak Noise Test Results

Page 61

If OVR (Overrange) is displayed, the Capacitance is greater than can be measured or the cable is properly connected.

Press the ESCAPE key to exit.

Impulse Noise Test Results

To display the IMPULSE NOISE screen, from the Ready screen, press Jack (F4) and set the Jack to Coax. Then press the Measure Cable Performance key, then select Impulse Noise.

During the Noise test, the cable can be open, shorted or terminated. There is no preference.

Press Clear (F2) to clear the graph.

Press Level (F4) to change the voltage level for detecting impulses.

Press the ESCAPE key to exit.

Peak-to-Peak Noise Test Results

To display the PEAK-TO-PEAK NOISE screen, from the Ready screen, press Jack (F4) and set the Jack to Coax. Then press the Measure Cable Performance key, then select P-P Noise.

During the Noise test, the cable can be open, shorted or terminated. There is no preference.

Press the ESCAPE key to exit.

4747 North 22nd Street Phoenix, AZ 85016-4708

(602) 952-6400 FAX (602) 952-6401

Microtest Europe

2A Kingfisher House, Northwood Park, Gatwick Road Crawley, West Sussex, RH102XN, United Kingdom +44 1293 894000, FAX +44 1293 894008

http://www.microtest.com

Part Number 2938-4509-03E Rev 1 3/96

Page 61

Image 61

Contents N t a S c a n n e r O d u c t F a m i l y E r G u i d e Introduction Ni-Cd Battery Scanner and 2-Way Injectors Charging the Scanner’s BatteryGetting Started Ready ScreenNi-Cd Battery Tips Way Injector+/2-Way Injector BatteryBattery Refresh Mode PentaScanner+ is in battery refresh modeTest Connectors Super Injector+/Super Injector BatteryHigh Voltage Protection Way Injector+/2-Way Injector LED IndicatorsPass FailWhen to Use the Injector Super Injector+/Super Injector LED IndicatorsCharging CircuitInjector Calibration Using Multiple InjectorsCalibration Connections Mod 8 Adapter NotePress the Extended Functions key Connections Basic Link with IDC Block and Modular 8 Jack Basic Link with Modular 8 JacksFull Channel Modular 8 Link Autotest Selecting the Cable Type Steps for Running AutotestExtended Functions key and select Calibrate Injector Calculating NVP Editing the Cable TypeEditing Autotest Information Customizing AutotestEditing the Autotest Name Selecting Tests to Run During Autotest Selecting Pairs for AutotestRunning Autotest Editing Test LimitsAutotest Results Screen Wire Map Test Results Wire MapViewing Autotest Results Customizing Length Limits LengthLength Test Results Propagation Delay Test Results Propagation Delay Customizing Delay LimitsNear End Crosstalk Next Measuring Next at Both Ends of the LinkNext Test Results Customizing Next LimitsNext Graph Next DetailAttenuation Attenuation Limits and Frequency Customizing Attenuation LimitsEditing Attenuation Limits Attenuation Detail Attenuation Test ResultsAttenuation Graph Attenuation-to-Crosstalk Ratio ACRACR Test Results Customizing ACR LimitsImpedance ISO Class DImpedance Test Results Customizing Impedance LimitsLoop Resistance Loop Resistance Test Results Customizing Loop Resistance LimitsCapacitance Customizing Capacitance LimitsSaving Autotest Results Capacitance Test ResultsPrinting Autotest Results Save Sweep DataViewing Autotest Results Summary Sample Autotest Report Editing with the Alphanumeric Keypad Editing, Printing & UpdatingEditing with the Arrow Keys Memory, then press Print F3 Printing or Downloading Test ResultsUploading Autotest Reports to Windows Terminal Printing TipsProcomm Plus for Windows Problem My printout is garbled. Why? Troubleshooting Printing ProblemsUpdating Scanner Software from the PC Downloading Software UpdatesWaiting for Reflash Updating the 2-Way Injector+/2-Way InjectorOne or more stored Autotest results have been lost World Wide Web Technical SupportPenta -C1 Download of Flash image file completeMicrotest Bulletin Board System BBS Find Cable FaultsFaxFacts Cross Wiring Wire Map for Both Ends of the LinkShort at the Injector End Short at the Scanner EndGraph F1 Measure Cable PerformanceAttenuation Limits Next SweepAttenuation Noise Length/DelayImpulse Noise Peak-to-Peak Noise Analyze LAN TrafficLAN Traffic Display Extended Functions Setting Up the Traffic MonitorExtended Functions Menu Autotest MemoryCalibrating the Injector Autotest SetupSetting Backlight and Auto Shutoff Times Setting Up User PreferencesSetting Up Units Editing Owner/Company NameSetting the Date and Time Setting Up the Printer PortSelecting a Graphics Printer Displaying Injector Information Appendix a SpecificationsTracing a Cable Locating an Office Cable DropUser Interface Wire MapEnvironmental Measurement PortsNear-End Crosstalk Next LengthAttenuation Loop Resistance ImpedanceCapacitance Impulse NoisePower Control Rechargeable BatteryHigh Voltage Input/Protection LED DisplaysSuper Injector+/Super Injector Physical Characteristics Way Injector+ Next Measurement Performance SpecificationsFeatures Working with 150 Ohm Cables Appendix B 150 ohm CablesCreating a Cat 5 Test for Token Ring EnvironmentCable Pin-outs Appendix C Cable Pin-outsPress Save F1 Serial Cable DB-9 Female to DB-9 Male Pin-outsAppendix D Working with Coaxial Cable Length/Delay Test Results Peak-to-Peak Noise Test Results Impulse Noise Test Results