Nintendo 2000 manual

Page 14

7.If the above screen appears, you must insert the Windows 98 CD so that Windows can copy the remaining files.

8. After files copying is done, you will see the following screen:

9. Click Finish to complete the installation. You will see the following screen.

User’ Guide

14

Image 14

Contents Orion Contents Nvram Tftp Mode of Operation Understand the Cable Modem’s Features Contact Your Local Cable OperatorSupplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items Not SuppliedInstalling the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software DriversUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable ModemUninstalling the USB Driver Select USB Composite Device and click Remove Click RefreshInstalling the Modem Using the Ethernet Port Enet LED on my cable modem is not lit Troubleshooting the Ethernet InstallationNone of the LEDs are on when I power on the Cable Modem Page Cable Modem LEDs and Connectors LEDs on the Front of the ModemConnectors on the Back of the Modem Telnet commands Getting HelpCMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Image PingUser-Level PasswordTracert Show ¾ show interface ethernet ¾ show interfaceCMshow interface ? CMshow interface ethernetCMshow interface usb CMshow running-config¾ show interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show cpe-limitCMshow downstream CMshow cpe-limit¾ show downstream Display downstream information ¾ show upstream¾ show nat timer ¾ show nat configCMshow nat config ¾ show ripCMshow access-list CMshow nat timer¾ show access-list ¾ show pppoe-forwarding Display PPPoE enable or disableHost-name CM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ host-name delete Delete host-nameCustomer-123host-name delete ¾ dhcp ip-pool delete¾ dhcp gateway ip address Set local Dhcp gateway ip address ¾ dhcp reserve-mac delete 1-16allCMnat static ipmapping add 64.168.39.3 ¾ dhcp dns delete 1~4/allOne to one mapping Port forwarding setting ¾ nat static ipmapping delete index/allCMnat static portmapping delete CMnat static ip disableCMnat static ip enable NAT static ipInterfaces CMnat static gateway¾ interface ethernet startup ¾ interface cable upstream channel id¾ interface usb shutdown ¾ interface cable rip send-version¾ interface cable startup ¾ interface usb startup¾ rip version 1/2/2b ¾ rip timer response 10-65535 second¾ rip silence-mode enable/disable CMrip key-chain 1 1 start-time 2002-04-20 ¾ rip defaultCMrip key-chain 1 1 key-string abcdefg Access-list ¾ web-access password string Set web-access password¾ pppoe-forwarding enabledisable CMaccess-list 21 permit 192.168.100.10¾ access-list delete list IDall CMcopy tftpconfig 68.5.203.15 4ips.txt¾ snmp community string ro ¾ reset¾ snmp community ¾ write¾ ip nat enable Bridge modeNAT mode Routing mode ¾ ip route enableNAT/Routing mode ¾ ip natroute enableAccessing the Web User Interface Web User Interface HomeCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Router/NAT configuration Bridge ModeWAN Interface NAT Mode Gateway LAN InterfaceReset SubmitRouter Mode Routing Protocol LAN Interface Delete Key ChainAdd NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support