Nintendo 2000 manual

Page 29

communications with your cable service provider.

•If your PC is connected to a hub or gateway, try connecting the PC directly into the cable modem.

•If you are using a cable splitter, try removing the splitter and connect the cable modem directly to the cable wall outlet. Wait several minutes for the cable modem to re-establish communications with your cable service provider.

•Your Ethernet or coaxial cable may be damaged. Try using another cable.

•If none of these suggestions work, contact your cable service provider for further assistance.

User’ Guide

29

Image 29

Contents Orion Contents Nvram Tftp Mode of Operation Contact Your Local Cable Operator Understand the Cable Modem’s FeaturesGather Supplied and Required Items Prepare Your Area for Cable Modem InstallationSupplied Not SuppliedInstalling the Software Drivers Before Hardware Connection Installing the Cable Modem Using the USB PortPage Page Installing the Software Drivers Installing the HardwareUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB InstallationSelect USB Composite Device and click Remove Click Refresh Uninstalling the USB DriverInstalling the Modem Using the Ethernet Port Enet LED on my cable modem is not lit Troubleshooting the Ethernet InstallationNone of the LEDs are on when I power on the Cable Modem Page LEDs on the Front of the Modem Cable Modem LEDs and ConnectorsConnectors on the Back of the Modem Getting Help Telnet commandsCMshow ? CMshow interTab CMshow interface Redisplaying a commandDebug Ping ImageUser-Level PasswordTracert Show CMshow interface ? ¾ show interface¾ show interface ethernet CMshow interface ethernetCMshow interface usb CMshow running-config¾ show interface usb Qpsk ¾ show cpe-limit ¾ show cpe-info Display CPE information¾ show downstream Display downstream information CMshow cpe-limitCMshow downstream ¾ show upstreamCMshow nat config ¾ show nat config¾ show nat timer ¾ show rip¾ show access-list CMshow nat timerCMshow access-list ¾ show pppoe-forwarding Display PPPoE enable or disableHost-name Customer-123host-name delete ¾ host-name delete Delete host-nameCM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ dhcp ip-pool delete¾ dhcp reserve-mac delete 1-16all ¾ dhcp gateway ip address Set local Dhcp gateway ip addressCMnat static ipmapping add 64.168.39.3 ¾ dhcp dns delete 1~4/allOne to one mapping ¾ nat static ipmapping delete index/all Port forwarding settingCMnat static ip enable CMnat static ip disableCMnat static portmapping delete NAT static ipCMnat static gateway Interfaces¾ interface cable upstream channel id ¾ interface ethernet startup¾ interface cable startup ¾ interface cable rip send-version¾ interface usb shutdown ¾ interface usb startup¾ rip version 1/2/2b ¾ rip timer response 10-65535 second¾ rip silence-mode enable/disable CMrip key-chain 1 1 start-time 2002-04-20 ¾ rip defaultCMrip key-chain 1 1 key-string abcdefg ¾ web-access password string Set web-access password Access-list¾ access-list delete list IDall CMaccess-list 21 permit 192.168.100.10¾ pppoe-forwarding enabledisable CMcopy tftpconfig 68.5.203.15 4ips.txt¾ snmp community ¾ reset¾ snmp community string ro ¾ write¾ ip nat enable Bridge modeNAT mode ¾ ip route enable Routing mode¾ ip natroute enable NAT/Routing modeWeb User Interface Home Accessing the Web User InterfaceCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Bridge Mode Router/NAT configurationReset NAT Mode Gateway LAN InterfaceWAN Interface SubmitRouter Mode Routing Protocol LAN Interface Delete Key ChainAdd NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support