Nintendo 2000 manual Routing mode, ¾ ip route enable

Page 60

Routing mode

¾ip route enable

Default setting for routing mode is RIPv2 with DHCP disabled automatically.

Example:

RIPv2 with MD5 authenication mode enable, key-string “abcdefg”

Public subnet 24.30.206.0/29

•(5) Static Public IPs 24.30.206.2~24.30.206.6

•Gateway IP address 24.30.206.1

Telnet commands:

CM>interface ethernet address 24.30.206.1 mask 255.255.255.248

CM>interface cable rip key-chain 1

CM>interface cable rip auth-mode md5

CM>rip key-chain 1 1 key-string abcdefg

CM>ip route enable

CM>reset

User’ Guide

60

Image 60

Contents Orion Contents Nvram Tftp Mode of Operation Understand the Cable Modem’s Features Contact Your Local Cable OperatorPrepare Your Area for Cable Modem Installation Gather Supplied and Required ItemsSupplied Not SuppliedInstalling the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software DriversUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable ModemUninstalling the USB Driver Select USB Composite Device and click Remove Click RefreshInstalling the Modem Using the Ethernet Port Troubleshooting the Ethernet Installation None of the LEDs are on when I power on the Cable ModemEnet LED on my cable modem is not lit Page Cable Modem LEDs and Connectors LEDs on the Front of the ModemConnectors on the Back of the Modem Telnet commands Getting HelpCMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Image PingPassword TracertUser-Level Show ¾ show interface CMshow interface ?¾ show interface ethernet CMshow interface ethernetCMshow running-config ¾ show interface usbCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show cpe-limitCMshow cpe-limit ¾ show downstream Display downstream informationCMshow downstream ¾ show upstream¾ show nat config CMshow nat config¾ show nat timer ¾ show ripCMshow nat timer ¾ show access-listCMshow access-list ¾ show pppoe-forwarding Display PPPoE enable or disableHost-name ¾ host-name delete Delete host-name Customer-123host-name deleteCM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ dhcp ip-pool delete¾ dhcp gateway ip address Set local Dhcp gateway ip address ¾ dhcp reserve-mac delete 1-16all¾ dhcp dns delete 1~4/all One to one mappingCMnat static ipmapping add 64.168.39.3 Port forwarding setting ¾ nat static ipmapping delete index/allCMnat static ip disable CMnat static ip enableCMnat static portmapping delete NAT static ipInterfaces CMnat static gateway¾ interface ethernet startup ¾ interface cable upstream channel id¾ interface cable rip send-version ¾ interface cable startup¾ interface usb shutdown ¾ interface usb startup¾ rip timer response 10-65535 second ¾ rip silence-mode enable/disable¾ rip version 1/2/2b ¾ rip default CMrip key-chain 1 1 key-string abcdefgCMrip key-chain 1 1 start-time 2002-04-20 Access-list ¾ web-access password string Set web-access passwordCMaccess-list 21 permit 192.168.100.10 ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable CMcopy tftpconfig 68.5.203.15 4ips.txt¾ reset ¾ snmp community¾ snmp community string ro ¾ writeBridge mode NAT mode¾ ip nat enable Routing mode ¾ ip route enableNAT/Routing mode ¾ ip natroute enableAccessing the Web User Interface Web User Interface HomeCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Router/NAT configuration Bridge ModeNAT Mode Gateway LAN Interface ResetWAN Interface SubmitRouter Mode Routing Protocol LAN Interface Key Chain AddDelete NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support