Nintendo 2000 manual

Page 15

10.Choose Yes to restart your computer.

11.After the computer is rebooted, verify that the USB LED is lit on the front of you cable modem. If not, refer to the troubleshooting section later in this chapter.

User’ Guide

15

Image 15

Contents Orion Contents Nvram Tftp Mode of Operation Contact Your Local Cable Operator Understand the Cable Modem’s FeaturesNot Supplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items SuppliedInstalling the Software Drivers Before Hardware Connection Installing the Cable Modem Using the USB PortPage Page Installing the Software Drivers Installing the HardwareUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide None of the LEDs is on when I power on the LAN Cable Modem Troubleshooting the USB InstallationSelect USB Composite Device and click Remove Click Refresh Uninstalling the USB DriverInstalling the Modem Using the Ethernet Port Troubleshooting the Ethernet Installation None of the LEDs are on when I power on the Cable ModemEnet LED on my cable modem is not lit Page LEDs on the Front of the Modem Cable Modem LEDs and ConnectorsConnectors on the Back of the Modem Getting Help Telnet commandsCMshow ? CMshow interTab CMshow interface Redisplaying a commandDebug Ping ImagePassword TracertUser-Level Show CMshow interface ethernet ¾ show interfaceCMshow interface ? ¾ show interface ethernetCMshow running-config ¾ show interface usbCMshow interface usb Qpsk ¾ show cpe-limit ¾ show cpe-info Display CPE information¾ show upstream CMshow cpe-limit¾ show downstream Display downstream information CMshow downstream¾ show rip ¾ show nat configCMshow nat config ¾ show nat timer¾ show pppoe-forwarding Display PPPoE enable or disable CMshow nat timer¾ show access-list CMshow access-listHost-name ¾ dhcp ip-pool delete ¾ host-name delete Delete host-nameCustomer-123host-name delete CM dhcp ip-pool 192.168.10.2 CMshow dhcp¾ dhcp reserve-mac delete 1-16all ¾ dhcp gateway ip address Set local Dhcp gateway ip address¾ dhcp dns delete 1~4/all One to one mappingCMnat static ipmapping add 64.168.39.3 ¾ nat static ipmapping delete index/all Port forwarding settingNAT static ip CMnat static ip disableCMnat static ip enable CMnat static portmapping deleteCMnat static gateway Interfaces¾ interface cable upstream channel id ¾ interface ethernet startup¾ interface usb startup ¾ interface cable rip send-version¾ interface cable startup ¾ interface usb shutdown¾ rip timer response 10-65535 second ¾ rip silence-mode enable/disable¾ rip version 1/2/2b ¾ rip default CMrip key-chain 1 1 key-string abcdefgCMrip key-chain 1 1 start-time 2002-04-20 ¾ web-access password string Set web-access password Access-listCMcopy tftpconfig 68.5.203.15 4ips.txt CMaccess-list 21 permit 192.168.100.10¾ access-list delete list IDall ¾ pppoe-forwarding enabledisable¾ write ¾ reset¾ snmp community ¾ snmp community string roBridge mode NAT mode¾ ip nat enable ¾ ip route enable Routing mode¾ ip natroute enable NAT/Routing modeWeb User Interface Home Accessing the Web User InterfaceCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Bridge Mode Router/NAT configurationSubmit NAT Mode Gateway LAN InterfaceReset WAN InterfaceRouter Mode Routing Protocol LAN Interface Key Chain AddDelete NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support