Nintendo 2000 manual ¾ interface ethernet startup, ¾ interface cable upstream channel id

Page 52

¾interface ethernet mac-address {mac address} Assign MAC address to ethernet interface.

Example:

CM>interface ethernet mac-address 0008.0E86.1118

CM>show interface ethernet

Interface Ethernet

MAC address: 0008.0E86.1118

IP address 192.168.100.1 subnet-mask 255.255.255.224

Link status: link

Mode: 100Mbps, full-duplex

¾interface ethernet rip {enabledisable} Enable/disable RIP on ethernet interface.

¾interface ethernet rip send-version {12}

Set RIP version 1 or version 2 on ethernet interface.

¾interface ethernet rip key-chain {12none} Set RIP key-chain to 1, 2, or none.

¾interface ethernet rip auth-mode { none md5 text} Set RIP authentication mode to none, md5, or text.

¾interface ethernet shutdown

Stop transmitting traffic on the ethernet interface.

¾interface ethernet startup

Start transmitting traffic on the ethernet interface.

¾interface cable upstream channel {id}

Change upstream channel ID.

¾interface cable downstream preset {frequency} Add frequency to downstream frequency preset table.

¾interface cable rip {enabledisable} Enable/disable RIP on cable interface.

User’ Guide

52

Image 52

Contents Orion Contents Nvram Tftp Mode of Operation Understand the Cable Modem’s Features Contact Your Local Cable OperatorPrepare Your Area for Cable Modem Installation Gather Supplied and Required ItemsSupplied Not SuppliedInstalling the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software DriversUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable ModemUninstalling the USB Driver Select USB Composite Device and click Remove Click RefreshInstalling the Modem Using the Ethernet Port None of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Page Cable Modem LEDs and Connectors LEDs on the Front of the ModemConnectors on the Back of the Modem Telnet commands Getting HelpCMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Image PingTracert PasswordUser-Level Show ¾ show interface CMshow interface ?¾ show interface ethernet CMshow interface ethernet¾ show interface usb CMshow running-configCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show cpe-limitCMshow cpe-limit ¾ show downstream Display downstream informationCMshow downstream ¾ show upstream¾ show nat config CMshow nat config¾ show nat timer ¾ show ripCMshow nat timer ¾ show access-listCMshow access-list ¾ show pppoe-forwarding Display PPPoE enable or disableHost-name ¾ host-name delete Delete host-name Customer-123host-name deleteCM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ dhcp ip-pool delete¾ dhcp gateway ip address Set local Dhcp gateway ip address ¾ dhcp reserve-mac delete 1-16allOne to one mapping ¾ dhcp dns delete 1~4/allCMnat static ipmapping add 64.168.39.3 Port forwarding setting ¾ nat static ipmapping delete index/allCMnat static ip disable CMnat static ip enableCMnat static portmapping delete NAT static ipInterfaces CMnat static gateway¾ interface ethernet startup ¾ interface cable upstream channel id¾ interface cable rip send-version ¾ interface cable startup¾ interface usb shutdown ¾ interface usb startup¾ rip silence-mode enable/disable ¾ rip timer response 10-65535 second¾ rip version 1/2/2b CMrip key-chain 1 1 key-string abcdefg ¾ rip defaultCMrip key-chain 1 1 start-time 2002-04-20 Access-list ¾ web-access password string Set web-access passwordCMaccess-list 21 permit 192.168.100.10 ¾ access-list delete list IDall¾ pppoe-forwarding enabledisable CMcopy tftpconfig 68.5.203.15 4ips.txt¾ reset ¾ snmp community¾ snmp community string ro ¾ writeNAT mode Bridge mode¾ ip nat enable Routing mode ¾ ip route enableNAT/Routing mode ¾ ip natroute enableAccessing the Web User Interface Web User Interface HomeCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Router/NAT configuration Bridge ModeNAT Mode Gateway LAN Interface ResetWAN Interface SubmitRouter Mode Routing Protocol LAN Interface Add Key ChainDelete NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support