Nintendo 2000 manual

Page 22

7.Click Finish to complete the installation.

8.After the installation is completed, verify that the USB LED is lit on the front of you cable modem. If not, refer to the troubleshooting section later in this chapter.

User’ Guide

22

Image 22

Contents Orion Contents Nvram Tftp Mode of Operation Understand the Cable Modem’s Features Contact Your Local Cable OperatorSupplied Prepare Your Area for Cable Modem InstallationGather Supplied and Required Items Not SuppliedInstalling the Cable Modem Using the USB Port Installing the Software Drivers Before Hardware ConnectionPage Page Installing the Hardware Installing the Software DriversUser’ Guide User’ Guide Page Page Page User’ Guide Page Click Yes to restart the computer User’ Guide Page Page Page Page Page Click Finish to complete the installation User’ Guide Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable ModemUninstalling the USB Driver Select USB Composite Device and click Remove Click RefreshInstalling the Modem Using the Ethernet Port None of the LEDs are on when I power on the Cable Modem Troubleshooting the Ethernet InstallationEnet LED on my cable modem is not lit Page Cable Modem LEDs and Connectors LEDs on the Front of the ModemConnectors on the Back of the Modem Telnet commands Getting HelpCMshow interTab CMshow interface Redisplaying a command CMshow ?Debug Image PingTracert PasswordUser-Level Show ¾ show interface ethernet ¾ show interfaceCMshow interface ? CMshow interface ethernet¾ show interface usb CMshow running-configCMshow interface usb Qpsk ¾ show cpe-info Display CPE information ¾ show cpe-limitCMshow downstream CMshow cpe-limit¾ show downstream Display downstream information ¾ show upstream¾ show nat timer ¾ show nat configCMshow nat config ¾ show ripCMshow access-list CMshow nat timer¾ show access-list ¾ show pppoe-forwarding Display PPPoE enable or disableHost-name CM dhcp ip-pool 192.168.10.2 CMshow dhcp ¾ host-name delete Delete host-nameCustomer-123host-name delete ¾ dhcp ip-pool delete¾ dhcp gateway ip address Set local Dhcp gateway ip address ¾ dhcp reserve-mac delete 1-16allOne to one mapping ¾ dhcp dns delete 1~4/allCMnat static ipmapping add 64.168.39.3 Port forwarding setting ¾ nat static ipmapping delete index/allCMnat static portmapping delete CMnat static ip disableCMnat static ip enable NAT static ipInterfaces CMnat static gateway¾ interface ethernet startup ¾ interface cable upstream channel id¾ interface usb shutdown ¾ interface cable rip send-version¾ interface cable startup ¾ interface usb startup¾ rip silence-mode enable/disable ¾ rip timer response 10-65535 second¾ rip version 1/2/2b CMrip key-chain 1 1 key-string abcdefg ¾ rip defaultCMrip key-chain 1 1 start-time 2002-04-20 Access-list ¾ web-access password string Set web-access password¾ pppoe-forwarding enabledisable CMaccess-list 21 permit 192.168.100.10¾ access-list delete list IDall CMcopy tftpconfig 68.5.203.15 4ips.txt¾ snmp community string ro ¾ reset¾ snmp community ¾ writeNAT mode Bridge mode¾ ip nat enable Routing mode ¾ ip route enableNAT/Routing mode ¾ ip natroute enableAccessing the Web User Interface Web User Interface HomeCable Modem Information Cable Modem Status Downstream Upstream Upstream Burst Operation Parameters Event Log Router/NAT configuration Bridge ModeWAN Interface NAT Mode Gateway LAN InterfaceReset SubmitRouter Mode Routing Protocol LAN Interface Add Key ChainDelete NAT Router Mode Routing Protocol Gateway LAN Interface Authentication mode Authentication Key Chain Reset Gateway LAN Setup Page Docsis configuration file Vsif tag support