Printronix T5000R user manual Shifting The Scanning Beam

Page 33

Cut Media Handling Mode

Shifting The Scanning Beam

This option enables you to shift the scanning beam horizontally to the left or right. The left edge of the beam should be approximately

0.13inches (3.3 mm) past the left edge of the tear bar. After you set this value, save it as part of the configuration for future use.

The value range is from –99 to 99. The default is 0. Lower values will move the beam to the left.

NOTE: You must set Admin User to Enable in the PRINTER CONTROL menu to access the Beam Shift option. (Refer to the User’s Manual.)

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press and at the same time to unlock the key.

.

3. If necessary, press .. until VALIDATOR displays.

4. Press until Validator Funct. displays.

5. Make sure Enable is selected.

6. Press until Beam Shift displays.

7. Press + or to scroll through the values: –99 to 99. The default is 0. Lower values will move the beam to the left. Press to accept the shift value.

Keep selecting the new value until the beam width is at the desired position. The left edge of beam should be approximately 0.13 inches (3.3 mm) from the left edge of the tear bar.

8. Save the configuration for future use.

33

Image 33
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesCE Notice European Union Taiwan Lithium Battery WarningTrademark Acknowledgements Table of Contents Contact Information Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesFactory Installation Installation and RemovalField Installation Prepare The PrinterInstallation and Removal Install The FerriteWrapping the Power/Data Cable Around the Ferrite Install The FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Installing the Lower Bracket Install The BracketsInstall The Brackets Attaching the Grounding Wire and Power/Data Cable Attach The Grounding Wire And Power/Data CableAttach The Grounding Wire And Power/Data Cable Restore The Printer To OperationEnable The Validator Enable The ValidatorAdjust The Scanning Beam Continuous, Tear-Off, and Tear-Off StripContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning Beam Peel-Off Media Handling ModeCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode To Move Beam To Rotate Beam Down Clockwise Counterclockwise Adjusting the Center of the Scanning BeamShifting The Scanning Beam Reset Button Settings Time Reset Button Is Depressed Result CalibrationCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Basic Validator Setup Unit PositioningValidator Front Panel Page Validator Menu Validator MenuCont. from previous Basic Validator Setup50% To 100% Configuring The Validator Configuring The ValidatorEnabling And Disabling The Validator Validator Reporting Setting Auto ReportRfid Encoder Requesting a Validator ReportSetting Auto Report Time To enable Auto ReportTo set the Auto Report Time Defining The Data Output Destination Telemetry Path Resetting Validator DataConfiguring The Validator Validator Statistics Validator StatisticsSetting Number Of Bar Codes On a Form Defining Validator OptionsChecking Quiet Zones Defining Validator Options Checking The Firmware Revision NumberSetting Overstrike Style Setting For Skip LabelsSetting I2of5 Checksum Num Retry Num RescanMax Retry Action Advanced Validator Options DecodeabilityAdvanced Validator Options Defects Percent DecodeOverall Grade Example Overall Grade CalculationsEC Min ModulationRmin Gain Symbol ContrastSN Threshold OffsetScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Sample Scan Profile Profile H Mag = Profile H Mag68~HLladdercode=JKCGN####anaddnalenstart=h184095000200 Print SettingsTitfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisOperation Print Speed LimitsMin. Code Height Bar Code Height Print Speed Limits To change the Min. Code HeightTo set the printer speed manually To change the Min. Code Gap Min. Code GapOn-Demand Printing On-Demand PrintingMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Overstrike StopStop & Retry Retry FormRescan Form Grade&ReportRescan&Stop Rescan&RetryError Action Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting TroubleshootingTroubleshooting the Validator Symptom Solution Error Messages Troubleshooting the ValidatorSymptom Solution Maintenance Troubleshooting the Validator Symptom Solution MaintenancePrintronix Customer Support Center Contact InformationCorporate Offices Printronix Supplies DepartmentIndex Index Index Index Page 179097-001

T5000R specifications

The Printronix T5000R is a robust and versatile industrial printer designed to meet the demanding needs of high-volume printing environments. Known for its reliability and efficiency, this printer excels in various applications ranging from logistics to manufacturing.

One of the standout features of the T5000R is its advanced thermal transfer and direct thermal printing technology. This allows for high-quality print outputs with sharp text and crisp graphics. The printer supports multiple widths of labels and tags, enabling it to accommodate a broad array of media types and sizes, which is crucial for businesses that require flexibility in their labeling solutions.

The T5000R is equipped with a high-speed print engine capable of producing up to 12 inches per second, significantly enhancing productivity. Its high-resolution print quality of up to 600 dpi ensures that barcodes, text, and images are rendered with exceptional clarity, making it an ideal choice for applications that require precision.

Connectivity is a strong suit of the T5000R, which features USB, Ethernet, and optional wireless interfaces, allowing seamless integration into existing IT infrastructures. This connectivity ensures that the printer can easily communicate with a variety of devices, including computers, tablets, and mobile devices, facilitating efficient workflows.

Furthermore, the T5000R is built with user-friendly controls and an intuitive interface, making it easy for operators to manage printing tasks and settings. The printer is designed for high durability, with features such as an all-metal construction that can withstand harsh industrial environments. This not only ensures longevity but also reduces the total cost of ownership for businesses.

Another significant characteristic of the T5000R is its energy-efficient design. Printronix has implemented technologies that minimize power consumption without compromising performance, aligning with modern sustainability initiatives.

In conclusion, the Printronix T5000R combines high-speed printing, advanced thermal technology, extensive connectivity options, and robust construction to deliver an exceptional printing solution for demanding industrial applications. Its user-friendly design and energy-efficient features further enhance its appeal, making it a preferred choice for organizations looking to streamline their printing processes.