Printronix T5000R user manual To the Quick Setup

Page 89

 

 

 

Error Messages

 

 

Table 6. Message List

 

 

 

 

 

 

 

 

Message

Explanation

 

Solution

 

 

 

 

 

 

 

 

 

Poor scanning

Data validation failure:

1. Check for a wrinkled

 

Check media

percent decode. The validator

 

ribbon or debris on

 

 

detected gross

 

media. Roll wrinkled

 

 

inconsistencies within the

 

area onto take-up

 

 

height of the bar code. These

 

spindle.

 

 

types of failures are likely

2.

Adjust the printhead

 

 

attributed to large blemishes

 

 

 

pressure blocks. (Refer

 

 

within the bar code, caused

 

 

 

 

to the Quick Setup

 

 

by ribbon wrinkle or debris on

 

 

 

 

Guide or User’s

 

 

media.

 

 

 

 

Manual.)

 

 

 

 

 

 

 

 

 

Poor scanning

Data validation failure:

1. Check that paper and

 

Inspect head

hardware defect. The

 

ribbon are clean,

 

 

validator detected

 

unwrinkled, and

 

 

unexpected dark spots in

 

installed correctly.

 

 

spaces or light spots in bars.

2.

Clean the printhead.

 

 

This usually indicates a poor

 

 

3.

If message reappears,

 

 

ribbon/media combination, a

 

 

dirty printhead, or a burned

 

replace the printhead.

 

 

pixel.

 

 

 

 

 

 

 

Speed Exceeds

Print Speed is set above the

This message only appears

 

Validator Limit

maximum allowed for bar

briefly, and the speed is

 

 

code printing by the validator

automatically reduced.

 

 

as the Power-Up

Make sure Min. Code

 

 

configuration with the

 

 

Height (page 74) and Min.

 

 

validator option installed.

 

 

Code Gap (page 76) are set

 

 

 

 

 

An attempt was made to set

correctly.

 

 

Print Speed above the

 

 

 

 

maximum allowed in the

 

 

 

 

QUICK SETUP menu or via

 

 

 

 

host software.

 

 

 

 

Maximum speed depends on

 

 

 

 

Min. Code Height and Min.

 

 

 

 

Code Gap.

 

 

 

 

 

 

 

 

89

Page 88 Page 90
Image 89
Page 88 Page 90
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesCE Notice European Union Taiwan Lithium Battery WarningTrademark Acknowledgements Table of Contents Contact Information Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesFactory Installation Installation and RemovalField Installation Prepare The PrinterInstallation and Removal Install The FerriteWrapping the Power/Data Cable Around the Ferrite Install The FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Installing the Lower Bracket Install The BracketsInstall The Brackets Attaching the Grounding Wire and Power/Data Cable Attach The Grounding Wire And Power/Data CableAttach The Grounding Wire And Power/Data Cable Restore The Printer To OperationEnable The Validator Enable The ValidatorContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning BeamContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning Beam Peel-Off Media Handling ModeCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode To Move Beam To Rotate Beam Down Clockwise Counterclockwise Adjusting the Center of the Scanning BeamShifting The Scanning Beam Calibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Page Validator Menu Validator MenuCont. from previous Basic Validator Setup50% To 100% Enabling And Disabling The Validator Configuring The ValidatorConfiguring The Validator Validator Reporting Setting Auto ReportRfid Encoder Requesting a Validator ReportTo set the Auto Report Time Setting Auto Report TimeTo enable Auto Report Defining The Data Output Destination Telemetry Path Resetting Validator DataConfiguring The Validator Validator Statistics Validator StatisticsChecking Quiet Zones Setting Number Of Bar Codes On a FormDefining Validator Options Defining Validator Options Checking The Firmware Revision NumberSetting Overstrike Style Setting For Skip LabelsSetting I2of5 Checksum Max Retry Action Num RetryNum Rescan Advanced Validator Options Advanced Validator OptionsDecodeability Defects Percent DecodeOverall Grade Example Overall Grade CalculationsEC Min ModulationRmin Gain Symbol ContrastSN Threshold OffsetScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Sample Scan Profile Profile H Mag = Profile H Mag68~HLladdercode=JKCGN####anaddnalenstart=h184095000200 Print SettingsTitfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisMin. Code Height Bar Code Height OperationPrint Speed Limits To set the printer speed manually Print Speed LimitsTo change the Min. Code Height To change the Min. Code Gap Min. Code GapOn-Demand Printing On-Demand PrintingMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Overstrike StopStop & Retry Retry FormRescan Form Grade&ReportRescan&Stop Rescan&RetryError Action Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingTroubleshooting Symptom Solution Error MessagesTroubleshooting the Validator Maintenance Troubleshooting the Validator Symptom Solution MaintenancePrintronix Customer Support Center Contact InformationCorporate Offices Printronix Supplies DepartmentIndex Index Index Index Page 179097-001

T5000R specifications

The Printronix T5000R is a robust and versatile industrial printer designed to meet the demanding needs of high-volume printing environments. Known for its reliability and efficiency, this printer excels in various applications ranging from logistics to manufacturing.

One of the standout features of the T5000R is its advanced thermal transfer and direct thermal printing technology. This allows for high-quality print outputs with sharp text and crisp graphics. The printer supports multiple widths of labels and tags, enabling it to accommodate a broad array of media types and sizes, which is crucial for businesses that require flexibility in their labeling solutions.

The T5000R is equipped with a high-speed print engine capable of producing up to 12 inches per second, significantly enhancing productivity. Its high-resolution print quality of up to 600 dpi ensures that barcodes, text, and images are rendered with exceptional clarity, making it an ideal choice for applications that require precision.

Connectivity is a strong suit of the T5000R, which features USB, Ethernet, and optional wireless interfaces, allowing seamless integration into existing IT infrastructures. This connectivity ensures that the printer can easily communicate with a variety of devices, including computers, tablets, and mobile devices, facilitating efficient workflows.

Furthermore, the T5000R is built with user-friendly controls and an intuitive interface, making it easy for operators to manage printing tasks and settings. The printer is designed for high durability, with features such as an all-metal construction that can withstand harsh industrial environments. This not only ensures longevity but also reduces the total cost of ownership for businesses.

Another significant characteristic of the T5000R is its energy-efficient design. Printronix has implemented technologies that minimize power consumption without compromising performance, aligning with modern sustainability initiatives.

In conclusion, the Printronix T5000R combines high-speed printing, advanced thermal technology, extensive connectivity options, and robust construction to deliver an exceptional printing solution for demanding industrial applications. Its user-friendly design and energy-efficient features further enhance its appeal, making it a preferred choice for organizations looking to streamline their printing processes.
Top Page Image Contents