Printronix T5000R user manual Index

Page 98

Index

Contrast too low / Check media, 88 Overall Grade / Fail, 88

Poor scanning / Check heat&head, 88 Poor scanning / Check media, 89 Poor scanning / Inspect head, 89 Speed Exceeds / Validator Limit, 89 Unscannable code / check media, 90 Validator not / communicating, 91

External device reporting, 47

F

Firmware revision, 51

Form parameters, 50

Full Report, 48

F/W Revision, 51

G

Gain, 61

Good Barcodes, 49

Good Forms, 49

Grade&Report, 83

Grading, bar code, 57

I

Installing the validator, 15

I2of5 Checksum, 53

L

Last BWD, 49

M

Maintenance, 94

Max Retry Action, 54

Min. Code Gap, 76

Min. Code Height, 74

Missing bar code, 78

Modulation, 59

N

Num Rescan, 54

Num Retry, 54 Number of Codes, 50 Number of codes on a form, 50

O

Offset, 62

On-demand printing, 77

Online Data Validator

See Validator

Overall Grade, 57

Overall Grade / Fail, 88

Overstrike Forms, 49

Overstrike Mode, 81

Overstrike Style, 52

P

Panel, 39

Parameters, 11

Percent Decode, 56

Poor scanning / Check heat&head, 88 Poor scanning / Check media, 89 Poor scanning / Inspect head, 89 Print Settings, 68

Print speed limits, 74

Printing reports, 45

Profile H Mag, 67

98

Image 98
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement DefinitionsTermination of License Agreement Communication Notices CanadaTaiwan Lithium Battery Warning CE Notice European UnionTrademark Acknowledgements Table of Contents Contact Information Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesField Installation Installation and RemovalFactory Installation Prepare The PrinterInstall The Ferrite Installation and RemovalInstall The Ferrite Wrapping the Power/Data Cable Around the FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Installing the Lower BracketInstall The Brackets Attach The Grounding Wire And Power/Data Cable Attaching the Grounding Wire and Power/Data CableRestore The Printer To Operation Attach The Grounding Wire And Power/Data CableEnable The Validator Enable The ValidatorContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning BeamContinuous, Tear-Off, and Tear-Off Strip Peel-Off Media Handling Mode Adjust The Scanning BeamCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode Adjusting the Center of the Scanning Beam To Move Beam To Rotate Beam Down Clockwise CounterclockwiseShifting The Scanning Beam Calibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Page Validator Menu Validator MenuBasic Validator Setup Cont. from previous50% To 100% Enabling And Disabling The Validator Configuring The ValidatorConfiguring The Validator Rfid Encoder Setting Auto ReportValidator Reporting Requesting a Validator ReportTo set the Auto Report Time Setting Auto Report TimeTo enable Auto Report Resetting Validator Data Defining The Data Output Destination Telemetry PathConfiguring The Validator Validator Statistics Validator StatisticsChecking Quiet Zones Setting Number Of Bar Codes On a FormDefining Validator Options Checking The Firmware Revision Number Defining Validator OptionsSetting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Max Retry Action Num RetryNum Rescan Advanced Validator Options Advanced Validator OptionsDecodeability Percent Decode DefectsOverall Grade Overall Grade Calculations ExampleModulation EC MinRmin Symbol Contrast GainOffset SN ThresholdScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Profile H Mag Sample Scan Profile Profile H Mag =Print Settings 68~HLladdercode=JKCGN####anaddnalenstart=h184095000200Titfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisMin. Code Height Bar Code Height OperationPrint Speed Limits To set the printer speed manually Print Speed LimitsTo change the Min. Code Height Min. Code Gap To change the Min. Code GapOn-Demand Printing On-Demand PrintingBar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Stop OverstrikeRetry Form Stop & RetryGrade&Report Rescan FormRescan&Retry Rescan&StopError Action Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingTroubleshooting Symptom Solution Error MessagesTroubleshooting the Validator Maintenance Maintenance Troubleshooting the Validator Symptom Solution Contact Information Printronix Customer Support CenterPrintronix Supplies Department Corporate OfficesIndex Index Index Index Page 179097-001