Printronix T5000R user manual Error Messages, Message List Explanation Solution

Page 86

Chapter 2 Bar Code Failures

Error Messages

The validator can detect a number of errors. When one of these errors occurs, the validator alerts the printer to perform the currently selected error action (see “Error Action” on page 79) and show the appropriate error message on the printer display. Validator error messages are explained in Table 6.

Table 6. Message List

Message

Explanation

Solution

 

 

 

 

 

 

Bar code fails

This message appears when

1. Press PAUSE to clear

Job has errors

at least one label in a batch of

the message.

 

labels has a data validation

2. Manually scan all the

 

error.

 

bar codes in the label

 

 

 

NOTE:

batch, then reprint the

 

This message appears only

bad labels.

 

when Validator Action is set to

 

 

Grade&Report.

 

 

 

 

Bar Code Improper

Data validation error: the bar

Fix the application so it

Data Format

code is not properly encoded.

sends data in the correct

 

For example, a check sum is

bar code format.

 

incorrect, a required number

 

 

of characters is not met, or

 

 

the required terminator

 

 

characters are not included.

 

 

This problem is almost

 

 

always caused by incorrect

 

 

form or host application

 

 

design.

 

 

 

 

86

Page 85 Page 87
Image 86
Page 85 Page 87
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement DefinitionsTermination of License Agreement Communication Notices CanadaTaiwan Lithium Battery Warning CE Notice European UnionTrademark Acknowledgements Table of Contents Contact Information Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesField Installation Installation and RemovalFactory Installation Prepare The PrinterInstall The Ferrite Installation and RemovalInstall The Ferrite Wrapping the Power/Data Cable Around the FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Installing the Lower BracketInstall The Brackets Attach The Grounding Wire And Power/Data Cable Attaching the Grounding Wire and Power/Data CableRestore The Printer To Operation Attach The Grounding Wire And Power/Data CableEnable The Validator Enable The ValidatorContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning BeamContinuous, Tear-Off, and Tear-Off Strip Peel-Off Media Handling Mode Adjust The Scanning BeamCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode Adjusting the Center of the Scanning Beam To Move Beam To Rotate Beam Down Clockwise CounterclockwiseShifting The Scanning Beam Calibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Page Validator Menu Validator MenuBasic Validator Setup Cont. from previous50% To 100% Enabling And Disabling The Validator Configuring The ValidatorConfiguring The Validator Rfid Encoder Setting Auto ReportValidator Reporting Requesting a Validator ReportTo set the Auto Report Time Setting Auto Report TimeTo enable Auto Report Resetting Validator Data Defining The Data Output Destination Telemetry PathConfiguring The Validator Validator Statistics Validator StatisticsChecking Quiet Zones Setting Number Of Bar Codes On a FormDefining Validator Options Checking The Firmware Revision Number Defining Validator OptionsSetting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Max Retry Action Num RetryNum Rescan Advanced Validator Options Advanced Validator OptionsDecodeability Percent Decode DefectsOverall Grade Overall Grade Calculations ExampleModulation EC MinRmin Symbol Contrast GainOffset SN ThresholdScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Profile H Mag Sample Scan Profile Profile H Mag =Print Settings 68~HLladdercode=JKCGN####anaddnalenstart=h184095000200Titfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisMin. Code Height Bar Code Height OperationPrint Speed Limits To set the printer speed manually Print Speed LimitsTo change the Min. Code Height Min. Code Gap To change the Min. Code GapOn-Demand Printing On-Demand PrintingBar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Stop OverstrikeRetry Form Stop & Retry Grade&Report Rescan FormRescan&Retry Rescan&StopError Action Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingTroubleshooting Symptom Solution Error MessagesTroubleshooting the Validator Maintenance Maintenance Troubleshooting the Validator Symptom SolutionContact Information Printronix Customer Support CenterPrintronix Supplies Department Corporate OfficesIndex Index Index Index Page 179097-001
Top Page Image Contents