Printronix T5000R user manual Advanced Validator Options

Page 65

Advanced Validator Options

The following is a sample scan report of a Code 39, 10 mil bar code containing "*RJS8702*" with a quiet zone violation:

ERROR:BarcSymbolOveraXMocodulatiimnsdeSCANogyabBarData:GadeilitytrastREPORTcode(%)(mils)[ST]RJS8702[ST]quiet(%)zonetooC096ode58(2.small9.391)

ScanTGodMaBaPeRmin/RmaxDfEdgeotCSralio.centDecdeDeviatictsScansBarContrastProfile(%)DeviationAvg(%)(%)(%)(%) 302-19238.43116004

This is executable menu that prints the scan reflectance profile of bar code placed in the validator scan beam.

NOTE: You will need a minimum installed label width of 2 inches to support the Scan Profile printout.

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until VALIDATOR displays.

4. Press ↑ until Scan Profile displays.

5. Place a bar code in the scan beam path.

6. Press ↵ to scan the bar code.

7. When prompted on the control panel, remove the scanned bar code.

8. Press ↵ to print the scan profile.

65

Image 65

Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesCE Notice European Union Taiwan Lithium Battery WarningTrademark Acknowledgements Table of Contents Contact Information Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesFactory Installation Installation and RemovalField Installation Prepare The PrinterInstallation and Removal Install The FerriteWrapping the Power/Data Cable Around the Ferrite Install The FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Installing the Lower Bracket Install The BracketsInstall The Brackets Attaching the Grounding Wire and Power/Data Cable Attach The Grounding Wire And Power/Data CableAttach The Grounding Wire And Power/Data Cable Restore The Printer To OperationEnable The Validator Enable The ValidatorContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning BeamContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning Beam Peel-Off Media Handling ModeCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode To Move Beam To Rotate Beam Down Clockwise Counterclockwise Adjusting the Center of the Scanning BeamShifting The Scanning Beam Calibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Page Validator Menu Validator MenuCont. from previous Basic Validator Setup50% To 100% Enabling And Disabling The Validator Configuring The ValidatorConfiguring The Validator Validator Reporting Setting Auto ReportRfid Encoder Requesting a Validator ReportTo set the Auto Report Time Setting Auto Report TimeTo enable Auto Report Defining The Data Output Destination Telemetry Path Resetting Validator DataConfiguring The Validator Validator Statistics Validator StatisticsChecking Quiet Zones Setting Number Of Bar Codes On a FormDefining Validator Options Defining Validator Options Checking The Firmware Revision NumberSetting Overstrike Style Setting For Skip LabelsSetting I2of5 Checksum Max Retry Action Num RetryNum Rescan Advanced Validator Options Advanced Validator OptionsDecodeability Defects Percent DecodeOverall Grade Example Overall Grade CalculationsEC Min ModulationRmin Gain Symbol Contrast SN Threshold OffsetScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Sample Scan Profile Profile H Mag = Profile H Mag68~HLladdercode=JKCGN####anaddnalenstart=h184095000200 Print SettingsTitfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisMin. Code Height Bar Code Height OperationPrint Speed Limits To set the printer speed manually Print Speed LimitsTo change the Min. Code Height To change the Min. Code Gap Min. Code GapOn-Demand Printing On-Demand PrintingMissing Bar Code Error Detection Bad Bar Code Error DetectionBar Code Failures Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Overstrike StopStop & Retry Retry FormRescan Form Grade&ReportRescan&Stop Rescan&RetryError Action Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingTroubleshooting Symptom Solution Error MessagesTroubleshooting the Validator Maintenance Troubleshooting the Validator Symptom Solution MaintenancePrintronix Customer Support Center Contact InformationCorporate Offices Printronix Supplies DepartmentIndex Index Index Index Page 179097-001