Printronix T5000R user manual Trademark Acknowledgements

Page 8

Printronix makes no representations or warranties of any kind regarding this material, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose. Printronix shall not be held responsible for errors contained herein or any omissions from this material or for any damages, whether direct, indirect, incidental or consequential, in connection with the furnishing, distribution, performance or use of this material. The information in this manual is subject to change without notice.

This document contains proprietary information protected by copyright. No part of this document may be reproduced, copied, translated or incorporated in any other material in any form or by any means, whether manual, graphic, electronic, mechanical or otherwise, without the prior written consent of Printronix.

COPYRIGHT © 2005, 2006 PRINTRONIX, INC. All rights reserved.

Trademark Acknowledgements

Printronix, LinePrinter Plus, IGP, and PGL are registered trademarks of Printronix, Inc.

Code V is a trademark of Quality Micro Systems, Inc.

IPDS is a trademark of International Business Machines Corporation.

SL5000r and T5000r are trademarks of Printronix, Inc.

Image 8
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement Definitions Termination of License Agreement Communication Notices CanadaTaiwan Lithium Battery Warning CE Notice European UnionTrademark Acknowledgements Table of Contents Contact Information Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesInstallation and Removal Factory InstallationField Installation Prepare The PrinterInstall The Ferrite Installation and RemovalInstall The Ferrite Wrapping the Power/Data Cable Around the FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Installing the Lower BracketInstall The Brackets Attach The Grounding Wire And Power/Data Cable Attaching the Grounding Wire and Power/Data CableRestore The Printer To Operation Attach The Grounding Wire And Power/Data CableEnable The Validator Enable The ValidatorContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning BeamContinuous, Tear-Off, and Tear-Off Strip Peel-Off Media Handling Mode Adjust The Scanning BeamCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode Adjusting the Center of the Scanning Beam To Move Beam To Rotate Beam Down Clockwise CounterclockwiseShifting The Scanning Beam Calibration Reset Button Settings Time Reset Button Is Depressed ResultCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Validator Front Panel Basic Validator SetupUnit Positioning Page Validator Menu Validator MenuBasic Validator Setup Cont. from previous50% To 100% Enabling And Disabling The Validator Configuring The ValidatorConfiguring The Validator Setting Auto Report Validator ReportingRfid Encoder Requesting a Validator ReportTo set the Auto Report Time Setting Auto Report TimeTo enable Auto Report Resetting Validator Data Defining The Data Output Destination Telemetry PathConfiguring The Validator Validator Statistics Validator StatisticsChecking Quiet Zones Setting Number Of Bar Codes On a FormDefining Validator Options Checking The Firmware Revision Number Defining Validator OptionsSetting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Max Retry Action Num RetryNum Rescan Advanced Validator Options Advanced Validator OptionsDecodeability Percent Decode DefectsOverall Grade Overall Grade Calculations ExampleModulation EC MinRmin Symbol Contrast GainOffset SN ThresholdScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Profile H Mag Sample Scan Profile Profile H Mag =Print Settings 68~HLladdercode=JKCGN####anaddnalenstart=h184095000200Titfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisMin. Code Height Bar Code Height OperationPrint Speed Limits To set the printer speed manually Print Speed LimitsTo change the Min. Code Height Min. Code Gap To change the Min. Code GapOn-Demand Printing On-Demand PrintingBad Bar Code Error Detection Missing Bar Code Error DetectionBar Code Failures Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Stop OverstrikeRetry Form Stop & RetryGrade&Report Rescan FormRescan&Retry Rescan&StopError Action Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting the Validator Symptom Solution TroubleshootingTroubleshooting Symptom Solution Error MessagesTroubleshooting the Validator Maintenance Maintenance Troubleshooting the Validator Symptom SolutionContact Information Printronix Customer Support CenterPrintronix Supplies Department Corporate OfficesIndex Index Index Index Page 179097-001