Printronix T5000R user manual Checking The Firmware Revision Number, Defining Validator Options

Page 51

Defining Validator Options

When set to Enable (the default), then the bar code quiet zone is included as part of the pass/fail criteria.

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until VALIDATOR displays.

4. Press ↓ until Quiet Zones displays.

5. Press + or – to scroll through the choices: Enable or Disable. The default is Enable.

6. Press ↵ to select the desired value.

7. Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

8. Press PAUSE again to put the printer online.

NOTE: The validator does not recognize x-dimensions greater than 40 mil with Quiet Zones enabled.

Checking The Firmware Revision Number

For troubleshooting purposes, you may need to reference the firmware revision number.

.

1. Press .. to take the printer offline and place the printer in Menu mode.

2. If necessary, press ↓ and ↵ at the same time to unlock the ↵ key.

.

3. If necessary, press .. until VALIDATOR displays.

4. Press ↓ until F/W Revision displays. The firmware revision number displays.

5. Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

6. Press PAUSE again to put the printer online.

51

Image 51

Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesCE Notice European Union Taiwan Lithium Battery WarningTrademark Acknowledgements Table of Contents Contact Information Operational Parameters OverviewOverview Tools And Materials You Will Need Parts ListSafety Notices Safety NoticesPrepare The Printer Installation and RemovalFactory Installation Field InstallationInstallation and Removal Install The FerriteWrapping the Power/Data Cable Around the Ferrite Install The FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Installing the Lower Bracket Install The BracketsInstall The Brackets Attaching the Grounding Wire and Power/Data Cable Attach The Grounding Wire And Power/Data CableAttach The Grounding Wire And Power/Data Cable Restore The Printer To OperationEnable The Validator Enable The ValidatorAdjust The Scanning Beam Continuous, Tear-Off, and Tear-Off StripContinuous, Tear-Off, and Tear-Off Strip Adjust The Scanning Beam Peel-Off Media Handling ModeCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode To Move Beam To Rotate Beam Down Clockwise Counterclockwise Adjusting the Center of the Scanning BeamShifting The Scanning Beam Reset Button Settings Time Reset Button Is Depressed Result CalibrationCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Basic Validator Setup Unit PositioningValidator Front Panel Page Validator Menu Validator MenuCont. from previous Basic Validator Setup50% To 100% Configuring The Validator Configuring The ValidatorEnabling And Disabling The Validator Requesting a Validator Report Setting Auto ReportValidator Reporting Rfid EncoderSetting Auto Report Time To enable Auto ReportTo set the Auto Report Time Defining The Data Output Destination Telemetry Path Resetting Validator Data Configuring The Validator Validator Statistics Validator StatisticsSetting Number Of Bar Codes On a Form Defining Validator OptionsChecking Quiet Zones Defining Validator Options Checking The Firmware Revision NumberSetting Overstrike Style Setting For Skip LabelsSetting I2of5 Checksum Num Retry Num RescanMax Retry Action Advanced Validator Options DecodeabilityAdvanced Validator Options Defects Percent DecodeOverall Grade Example Overall Grade CalculationsEC Min ModulationRmin Gain Symbol ContrastSN Threshold OffsetScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Sample Scan Profile Profile H Mag = Profile H Mag68~HLladdercode=JKCGN####anaddnalenstart=h184095000200 Print SettingsTitfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisOperation Print Speed LimitsMin. Code Height Bar Code Height Print Speed Limits To change the Min. Code HeightTo set the printer speed manually To change the Min. Code Gap Min. Code GapOn-Demand Printing On-Demand PrintingBar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Overstrike StopStop & Retry Retry FormRescan Form Grade&ReportRescan&Stop Rescan&RetryError Action Message List Explanation Solution Error MessagesError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting TroubleshootingTroubleshooting the Validator Symptom Solution Error Messages Troubleshooting the ValidatorSymptom Solution Maintenance Troubleshooting the Validator Symptom Solution MaintenancePrintronix Customer Support Center Contact InformationCorporate Offices Printronix Supplies DepartmentIndex Index Index Index Page 179097-001