Printronix T5000R user manual Sample Scan Profile

Page 66

Chapter 2 Configuring The Validator

9.Press ↓ and ↵ at the same time to lock the ↵ key, then press PAUSE to take the printer offline.

10.Press PAUSE again to put the printer online.

The length of the scan profile printed is proportional to the Beam Width setting (page 71) and depends on the Profile H Mag setting (page 67).

The scan profile will print either a 1.5 inch wide or a 3 inch wide graph depending on the Label Width setting (in the MEDIA CONTROL menu). (Label widths less than 4 inches print the smaller 1.5 inch wide profile.)

Printing is done in continuous mode without taking into account media gap/marks.

NOTE: Use continuous media or else the scan profile may distort at the media gap/marks.

The following figure shows a sample scan profile graph. It only shows the profile of actual bar code data. The dashed lines represent the 90% and 10% marks. You can use these to help set the gain and offset (if necessary).

Figure 17. Sample Scan Profile

66

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Online Data Validator User’s Manual Page Online Data Validator User’s Manual Software License Agreement DefinitionsTermination of License Agreement Communication Notices CanadaTaiwan Lithium Battery Warning CE Notice European UnionTrademark Acknowledgements Table of Contents Contact Information Overview Operational ParametersOverview Parts List Tools And Materials You Will NeedSafety Notices Safety NoticesField Installation Installation and RemovalFactory Installation Prepare The PrinterInstall The Ferrite Installation and RemovalInstall The Ferrite Wrapping the Power/Data Cable Around the FerriteInserting the Wire Saddle Into the Frame Boss Install The Ferrite Adding the Grommet to the Power/Data Cable Position the Ferrite Install The Brackets Installing the Lower BracketInstall The Brackets Attach The Grounding Wire And Power/Data Cable Attaching the Grounding Wire and Power/Data CableRestore The Printer To Operation Attach The Grounding Wire And Power/Data CableEnable The Validator Enable The ValidatorAdjust The Scanning Beam Continuous, Tear-Off, and Tear-Off StripContinuous, Tear-Off, and Tear-Off Strip Peel-Off Media Handling Mode Adjust The Scanning BeamCut Media Handling Mode Cut Media Handling ModeScanning Beam Adjustment Screws Cut Media Handling Mode Adjusting the Center of the Scanning Beam To Move Beam To Rotate Beam Down Clockwise CounterclockwiseShifting The Scanning Beam Reset Button Settings Time Reset Button Is Depressed Result CalibrationCalibration Calibrating the Validator Bar Code Validation Demo Bar Code Validation Demo Calibration Basic Validator Setup Unit PositioningValidator Front Panel Page Validator Menu Validator MenuBasic Validator Setup Cont. from previous50% To 100% Configuring The Validator Configuring The ValidatorEnabling And Disabling The Validator Rfid Encoder Setting Auto ReportValidator Reporting Requesting a Validator ReportSetting Auto Report Time To enable Auto ReportTo set the Auto Report Time Resetting Validator Data Defining The Data Output Destination Telemetry PathConfiguring The Validator Validator Statistics Validator StatisticsSetting Number Of Bar Codes On a Form Defining Validator OptionsChecking Quiet Zones Checking The Firmware Revision Number Defining Validator OptionsSetting For Skip Labels Setting Overstrike StyleSetting I2of5 Checksum Num Retry Num RescanMax Retry Action Advanced Validator Options DecodeabilityAdvanced Validator Options Percent Decode DefectsOverall Grade Overall Grade Calculations ExampleModulation EC MinRmin Symbol Contrast GainOffset SN ThresholdScan Report Scan Report Information Advanced Validator Options Sample Scan Profile Profile H Mag Sample Scan Profile Profile H Mag =Print Settings 68~HLladdercode=JKCGN####anaddnalenstart=h184095000200Titfp 255 Scanner Settings Beam Width Beam Shift General Process For Barcode Analysis General Process For Barcode AnalysisOperation Print Speed LimitsMin. Code Height Bar Code Height Print Speed Limits To change the Min. Code HeightTo set the printer speed manually Min. Code Gap To change the Min. Code GapOn-Demand Printing On-Demand PrintingBar Code Failures Bad Bar Code Error DetectionMissing Bar Code Error Detection Bar Code FailuresError Action Error ActionForms Printed After an Error Detection Stop OverstrikeRetry Form Stop & RetryGrade&Report Rescan FormRescan&Retry Rescan&StopError Action Error Messages Message List Explanation SolutionError Messages Message List Explanation Solution Bar Code Failures Message List Explanation Solution To the Quick Setup Bar Code Failures Message List Explanation Solution Error Messages Message List Explanation Solution Troubleshooting TroubleshootingTroubleshooting the Validator Symptom Solution Error Messages Troubleshooting the ValidatorSymptom Solution Maintenance Maintenance Troubleshooting the Validator Symptom SolutionContact Information Printronix Customer Support CenterPrintronix Supplies Department Corporate OfficesIndex Index Index Index Page 179097-001

T5000R specifications

The Printronix T5000R is a robust and versatile industrial printer designed to meet the demanding needs of high-volume printing environments. Known for its reliability and efficiency, this printer excels in various applications ranging from logistics to manufacturing.

One of the standout features of the T5000R is its advanced thermal transfer and direct thermal printing technology. This allows for high-quality print outputs with sharp text and crisp graphics. The printer supports multiple widths of labels and tags, enabling it to accommodate a broad array of media types and sizes, which is crucial for businesses that require flexibility in their labeling solutions.

The T5000R is equipped with a high-speed print engine capable of producing up to 12 inches per second, significantly enhancing productivity. Its high-resolution print quality of up to 600 dpi ensures that barcodes, text, and images are rendered with exceptional clarity, making it an ideal choice for applications that require precision.

Connectivity is a strong suit of the T5000R, which features USB, Ethernet, and optional wireless interfaces, allowing seamless integration into existing IT infrastructures. This connectivity ensures that the printer can easily communicate with a variety of devices, including computers, tablets, and mobile devices, facilitating efficient workflows.

Furthermore, the T5000R is built with user-friendly controls and an intuitive interface, making it easy for operators to manage printing tasks and settings. The printer is designed for high durability, with features such as an all-metal construction that can withstand harsh industrial environments. This not only ensures longevity but also reduces the total cost of ownership for businesses.

Another significant characteristic of the T5000R is its energy-efficient design. Printronix has implemented technologies that minimize power consumption without compromising performance, aligning with modern sustainability initiatives.

In conclusion, the Printronix T5000R combines high-speed printing, advanced thermal technology, extensive connectivity options, and robust construction to deliver an exceptional printing solution for demanding industrial applications. Its user-friendly design and energy-efficient features further enhance its appeal, making it a preferred choice for organizations looking to streamline their printing processes.
Top Page Image Contents