Printronix P7000 H-Series, PSA3 manual Enable Upper Control Codes, Font Expansion

Page 43

Enable Upper Control Codes

Enable Upper Control Codes

ASCII Code

ESC 7

Hex Code

1B 37

Dec Code

27 55

Purpose

Tells the printer to treat codes from 128 to 159 as control codes

 

instead of printable characters.

Comment

This command affects the front panel setting of “Alt. Set 80-9F.”

 

In the default mode, codes 128 to 159 are treated as printable

 

characters.

Font Expansion

ASCII Code

ASSC

0

e

n1

n2

Hex Code

ASSC

30

65

n1

n2

Dec Code

ASSC

48

101

n1

n2

Purpose Expand the DBCS character up to the size of 72.

For this command to work, n1 must be the same value as n2 (i.e. n1 = n2). When n1 and n2 = 25 to 72, this set font expansion mode is ON. The value of n1 and n2 will determine the bitmap size. For example, if the size of n1 is 50, then the size of the bitmap will be set to 50x50. For n1 and n2 = 24, the font expansion mode will reset to OFF and the bitmap size reverts to the default, 24x24.

Inter-line spacing and inter-character spacing calculations are based on standard setting as if bitmap is 24x24. This command will only increase the size of the bitmap and not affect inter- character spacing or inter-line spacing. For example, if inter- line spacing is 6 dot rows, when the bitmap is expanded from 24x24 to 72x72, the inter-line spacing still remains as 6 dot rows. This is the same for inter-character spacing.

Other commands, such as double height, double width, 2x2 times, left/right margin etc., will not function when font expansion mode is set on. For different typefaces, the characters will expand based on approximate typeface resolution. All commands affecting LPI and CPI will still take effect and is set based on the bitmap being 24x24.

Where:

n1 = 24 ~ 72

n2 = 24 ~ 72

This control code does not function while in non-DBCS mode.

43

Image 43
Contents Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table About This Manual Software FeaturesRelated Product Information Software Features Control Panel IntroductionPrinting The Configuration Printing The ConfigurationAllows you to make configuration changes Printing Configurations Step Key ResultLocks the Enter key Configuration Menu Overview Configuration MenuConfiguration Menu Moving Within The Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus MenuCPI/LPI Select Font Attributes Perforation Skip Form LengthForm Width MarginsKssm Emulation Kssm EmulationDefine CR Code Exceptions And Differences Kssm EmulationFactory Settings Characteristic Default Setting Default Values And StatesFS Sequences Escape SequencesFormat For Control Code Descriptions Configuring The Kssm Emulation With Control CodesSuper-Set Commands Set And Reset CodesControl Code Index Setting the Page FormatSetting the Units Control Code IndexControl-code Character Printing Selecting CharactersMechanical Control Printing Graphics Hangul Extension CommandsData and Memory Control Align Sbcs Character with Dbcs Character Advance Print Position VerticallyAscii Code Hex Code Dec Code Purpose Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With BackspaceAscii Hex Selects Barcode Barcode PrintingOffset unit Barcode Printing Ascii Selects ValueInch UPC-A UPC-E EAN Beeper Cancel LineBeeper Carriage ReturnDefine User-Defined Character Define Pattern for Special Printing EffectHex Code Dec Code Define User-Defined Chinese CharacterDelete Last Character in Buffer Define User-Defined Chinese CharacterDivided Hangul Double Height Enable Printing of Upper Control CodesEnable Upper Control Codes Enable Upper Control CodesFont Expansion Graphic Printing Form FeedInitialize Printer Graphics Printing Select Bit ImageGraphics Printing Select Bit Image Line Feed Bit On/Off Hex Dec Function Equivalent Master SelectMaster Select Ascii Code ESC ! n Hex CodeAscii Code FS ! n Hex Code Master Select In Dbcs ModeBit On/Off Hex Dec Function Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Pair Two Characters in Vertical PrintingSelect 1/6-inch Line Spacing Reassign Bit-image ModeSelect 1/8-inch Line Spacing Select 10 CPI Select 10 CPISelect 12 CPI Select 15 CPISelect 120-dpi Graphics Select 60-dpi GraphicsSelect 120-dpi Graphics Select 240-dpi GraphicsUSA Select an International Character SetSelect Bit Image Select Bit ImageSelect Bold Font Cancel Bold FontSelect Character Style Ascii Code ESC t n Hex Code Select Character TableSelect Condensed Printing Select Character TableCancel Condensed Printing Select Dbcs Print Quality Cancel Double-strike PrintingSelect Dbcs Print Quality Select Double-strike PrintingSelect Double-width Printing One Line Cancel Double-width Printing One LineCancel Double-width Printing in Dbcs Mode One Line Select Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Ascii Code Hex Code Select Dbcs ModeCancel Dbcs Mode Select Hangul Myunjo/Gothic StyleSelect Italic Font Cancel Italic FontSelect Italic Font Select Print QualityDeselect Printer Select PrinterSelect Superscript/Subscript Printing Select Vertical Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Dbcs Super/Subscript PrintingSet n/60-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/180-inch Line Spacing Set Absolute Horizontal Print Position Cancel Bottom MarginSet Absolute Horizontal Print Position Set Bottom MarginAscii Code ESC D n1 n2 … nk NUL Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Set Horizontal TabsSet Intercharacter Space Set Intercharacter SpaceSet Left Margin Set Page Length In Lines Set Page Length In InchesSet Page Length In Inches Set Right Margin Set Relative Horizontal Print PositionAscii Code ESC B n1 n2 … nk NUL Set Vertical Tab ChannelsSet Vertical Tabs Set Vertical Tab ChannelsAscii Code ESC b m n1 … nk NUL Set Vertical Tabs In VFU ChannelsDec Code 27 98 m n1 … nk Tab Vertically Tab HorizontallyTab Horizontally Turn Double-Height Printing On/Off Turn Auto-wrap Around On/OffTurn Double-Width Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn On/Off Ocrb Selection Turn Extending Table Character On/OffAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Korean Standard Code Table KSC5601 Code TableAppendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Supplies Department Printronix Customer Support CenterAppendix C Contact Information Corporate OfficesIndex Page Page 100 Page 179981-001