Printronix PSA3 Cancel Vertical Printing Select Horizontal Printing, Set n/60-inch Line Spacing

Page 66

Chapter 3 Configuring The KSSM Emulation With Control Codes

Cancel Vertical Printing (Select Horizontal Printing)

ASCII Code	FS K
Hex Code	28 4B
Dec Code	1C 75
Purpose	Prints all characters horizontally.
Comment	This command cancels vertical printing set with the FS J
	command.
	This is the default setting at power-up.
	The default is Normal (horizontal).

Set n/60-inch Line Spacing

ASCII Code	ESC A n
Hex Code	1B 41 n
Dec Code	27 65 n
Purpose	Sets the line spacing to n/60 inch.
	Where:
	0 < n <= 85
Comment	Changing the line spacing does not affect previous settings for
	vertical tabs or page length.
	Does not support 0 lpi. When n = 0, the printer prints according
	to the previous LPI.
	This command affects the front panel setting of “Select LPI.”

Set n/180-inch Line Spacing

ASCII Code	ESC 3 n
Hex Code	1B 33 n
Dec Code	27 51 n
Purpose	Sets the line spacing to n/180 inch.
	Where:
	0 < n <= 255
Comment	Changing the line spacing does not affect previous settings for
	vertical tabs or page length.
	Does not support 0 lpi. When n = 0, the printer prints according
	to the previous lpi.
	This command affects the front panel setting of “Select LPI.”

66

Image 66

Contents Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Software Features About This ManualRelated Product Information Software Features Introduction Control PanelPrinting The Configuration Printing The ConfigurationPrinting Configurations Step Key Result Allows you to make configuration changesLocks the Enter key Configuration Menu Configuration Menu OverviewMoving Within The Configuration Menu Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus MenuCPI/LPI Select Font Attributes Margins Form LengthForm Width Perforation SkipKssm Emulation Kssm EmulationDefine CR Code Kssm Emulation Exceptions And DifferencesDefault Values And States Factory Settings Characteristic Default SettingEscape Sequences FS SequencesSet And Reset Codes Configuring The Kssm Emulation With Control CodesSuper-Set Commands Format For Control Code DescriptionsControl Code Index Setting the Page FormatSetting the Units Control Code IndexSelecting Characters Control-code Character PrintingMechanical Control Hangul Extension Commands Printing GraphicsData and Memory Control Advance Print Position Vertically Align Sbcs Character with Dbcs CharacterBackspace Cancel The Alignment of Sbcs Character With Dbcs CharacterCancel The Alignment of Sbcs Character With Ascii Code Hex Code Dec Code PurposeBarcode Printing Ascii Hex Selects BarcodeBarcode Printing Ascii Selects Value Offset unitInch UPC-A UPC-E EAN Carriage Return Cancel LineBeeper BeeperDefine Pattern for Special Printing Effect Define User-Defined CharacterDefine User-Defined Chinese Character Define User-Defined Chinese CharacterDelete Last Character in Buffer Hex Code Dec CodeEnable Printing of Upper Control Codes Divided Hangul Double HeightEnable Upper Control Codes Enable Upper Control CodesFont Expansion Form Feed Graphic PrintingGraphics Printing Select Bit Image Initialize PrinterGraphics Printing Select Bit Image Line Feed Ascii Code ESC ! n Hex Code Master SelectMaster Select Bit On/Off Hex Dec Function EquivalentMaster Select In Dbcs Mode Ascii Code FS ! n Hex CodePair Two Characters in Vertical Printing Master Select One-Line Attribute In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Bit On/Off Hex Dec FunctionReassign Bit-image Mode Select 1/6-inch Line SpacingSelect 1/8-inch Line Spacing Select 15 CPI Select 10 CPISelect 12 CPI Select 10 CPISelect 60-dpi Graphics Select 120-dpi GraphicsSelect 240-dpi Graphics Select 120-dpi GraphicsSelect an International Character Set USASelect Bit Image Select Bit ImageCancel Bold Font Select Bold FontSelect Character Style Select Character Table Select Character TableSelect Condensed Printing Ascii Code ESC t n Hex CodeCancel Condensed Printing Select Double-strike Printing Cancel Double-strike PrintingSelect Dbcs Print Quality Select Dbcs Print QualityCancel Double-width Printing One Line Select Double-width Printing One LineSelect Double-width Printing in Dbcs Mode One Line Cancel Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Select Hangul Myunjo/Gothic Style Select Dbcs ModeCancel Dbcs Mode Ascii Code Hex CodeSelect Print Quality Cancel Italic FontSelect Italic Font Select Italic FontSelect Printer Deselect PrinterSelect Superscript/Subscript Printing Select Dbcs Super/Subscript Printing Cancel Superscript/Subscript PrintingCancel Superscript/Subscript Printing Select Vertical PrintingCancel Vertical Printing Select Horizontal Printing Set n/60-inch Line SpacingSet n/180-inch Line Spacing Set Bottom Margin Cancel Bottom MarginSet Absolute Horizontal Print Position Set Absolute Horizontal Print PositionSet Horizontal Tabs Cancel Dbcs Character Half Width Super/Subscript PrintingSet Dbcs Character Half Width Ascii Code ESC D n1 n2 … nk NULSet Intercharacter Space Set Intercharacter SpaceSet Left Margin Set Page Length In Inches Set Page Length In LinesSet Page Length In Inches Set Relative Horizontal Print Position Set Right MarginSet Vertical Tab Channels Set Vertical Tab ChannelsSet Vertical Tabs Ascii Code ESC B n1 n2 … nk NULSet Vertical Tabs In VFU Channels Ascii Code ESC b m n1 … nk NULDec Code 27 98 m n1 … nk Tab Horizontally Tab VerticallyTab Horizontally Turn Auto-wrap Around On/Off Turn Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Double-Width Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Extending Table Character On/Off Turn On/Off Ocrb SelectionAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies DepartmentCorporate Offices Appendix C Contact InformationIndex Page Page 100 Page 179981-001