Printronix PSA3 manual Select Printer, Deselect Printer, Select Superscript/Subscript Printing

Page 64

Chapter 3 Configuring The KSSM Emulation With Control Codes

Select Printer

ASCII Code	DC1
Hex Code	11
Dec Code	17
Purpose	Selects the printer after it has been deselected with the DC3
	command.
Comment	The printer ignores this command if the user has set the printer
	offline by pressing the online button.

Deselect Printer

ASCII Code	DC3
Hex Code	13
Dec Code	19
Purpose	Deselects the printer.
Comment	The printer cannot be reselected by pressing the online button.

Select Superscript/Subscript Printing

ASCII Code	ESC S n
Hex Code	1B 53 n
Dec Code	27 83 n
Purpose	Prints characters that follow at about 2/3 their normal height;
	the printing location depends on the value of n as follows:
	n = 1 or 49Lower part of the character space
	n = 0 or 48Upper part of the character space
	Where:
	n = 0, 1, 48, 49
Comment	This command does not affect graphics characters.
	The width of super/subscript characters when using
	proportional spacing is the same as that of normal characters.
	The underline strikes through the descenders on subscript
	characters during underline mode.
	Use the ESC T command to cancel super/subscript printing.
	This command only takes effect in SBCS mode.
	The default is Normal (non-super/subscript) printing.

64

Image 64

Contents Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table About This Manual Software FeaturesRelated Product Information Software Features Introduction Control PanelPrinting The Configuration Printing The ConfigurationPrinting Configurations Step Key Result Allows you to make configuration changesLocks the Enter key Configuration Menu Configuration Menu OverviewConfiguration Menu Moving Within The Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus MenuCPI/LPI Select Font Attributes Form Length Form WidthMargins Perforation SkipKssm Emulation Kssm EmulationDefine CR Code Kssm Emulation Exceptions And DifferencesDefault Values And States Factory Settings Characteristic Default SettingEscape Sequences FS SequencesConfiguring The Kssm Emulation With Control Codes Super-Set CommandsSet And Reset Codes Format For Control Code DescriptionsSetting the Page Format Setting the UnitsControl Code Index Control Code IndexControl-code Character Printing Selecting CharactersMechanical Control Printing Graphics Hangul Extension CommandsData and Memory Control Advance Print Position Vertically Align Sbcs Character with Dbcs CharacterCancel The Alignment of Sbcs Character With Dbcs Character Cancel The Alignment of Sbcs Character WithBackspace Ascii Code Hex Code Dec Code PurposeBarcode Printing Ascii Hex Selects BarcodeOffset unit Barcode Printing Ascii Selects ValueInch UPC-A UPC-E EAN Cancel Line BeeperCarriage Return BeeperDefine Pattern for Special Printing Effect Define User-Defined CharacterDefine User-Defined Chinese Character Delete Last Character in BufferDefine User-Defined Chinese Character Hex Code Dec CodeEnable Printing of Upper Control Codes Divided Hangul Double HeightEnable Upper Control Codes Enable Upper Control CodesFont Expansion Form Feed Graphic PrintingInitialize Printer Graphics Printing Select Bit ImageGraphics Printing Select Bit Image Line Feed Master Select Master SelectAscii Code ESC ! n Hex Code Bit On/Off Hex Dec Function EquivalentMaster Select In Dbcs Mode Ascii Code FS ! n Hex CodeMaster Select One-Line Attribute In Dbcs Mode Master Select One-Line Attribute In Dbcs ModePair Two Characters in Vertical Printing Bit On/Off Hex Dec FunctionSelect 1/6-inch Line Spacing Reassign Bit-image ModeSelect 1/8-inch Line Spacing Select 10 CPI Select 12 CPISelect 15 CPI Select 10 CPISelect 60-dpi Graphics Select 120-dpi GraphicsSelect 240-dpi Graphics Select 120-dpi GraphicsSelect an International Character Set USASelect Bit Image Select Bit ImageSelect Bold Font Cancel Bold FontSelect Character Style Select Character Table Select Condensed PrintingSelect Character Table Ascii Code ESC t n Hex CodeCancel Condensed Printing Cancel Double-strike Printing Select Dbcs Print QualitySelect Double-strike Printing Select Dbcs Print QualityCancel Double-width Printing One Line Select Double-width Printing One LineCancel Double-width Printing in Dbcs Mode One Line Select Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Select Dbcs Mode Cancel Dbcs ModeSelect Hangul Myunjo/Gothic Style Ascii Code Hex CodeCancel Italic Font Select Italic FontSelect Print Quality Select Italic FontDeselect Printer Select PrinterSelect Superscript/Subscript Printing Cancel Superscript/Subscript Printing Cancel Superscript/Subscript PrintingSelect Dbcs Super/Subscript Printing Select Vertical PrintingSet n/60-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/180-inch Line Spacing Cancel Bottom Margin Set Absolute Horizontal Print PositionSet Bottom Margin Set Absolute Horizontal Print PositionCancel Dbcs Character Half Width Super/Subscript Printing Set Dbcs Character Half WidthSet Horizontal Tabs Ascii Code ESC D n1 n2 … nk NULSet Intercharacter Space Set Intercharacter SpaceSet Left Margin Set Page Length In Lines Set Page Length In InchesSet Page Length In Inches Set Relative Horizontal Print Position Set Right MarginSet Vertical Tab Channels Set Vertical TabsSet Vertical Tab Channels Ascii Code ESC B n1 n2 … nk NULAscii Code ESC b m n1 … nk NUL Set Vertical Tabs In VFU ChannelsDec Code 27 98 m n1 … nk Tab Vertically Tab HorizontallyTab Horizontally Turn Auto-wrap Around On/Off Turn Double-Height Printing On/OffTurn Double-Width Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn On/Off Ocrb Selection Turn Extending Table Character On/OffAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies DepartmentCorporate Offices Appendix C Contact InformationIndex Page Page 100 Page 179981-001