Printronix PSA3, P7000 H-Series manual Set Dbcs Character Half Width, Set Horizontal Tabs

Page 68

Chapter 3 Configuring The KSSM Emulation With Control Codes

Set DBCS Character Half Width

ASCII Code	FS SI
Hex Code	28 0F
Dec Code	1C 15
Purpose	Prints DBCS characters that follow at about half their normal
	width, and SBCS characters maintain their normal width.
Comment	Use the FS DC2 command to cancel half-width DBCS
	character printing.
	This command resets subscript/ superscript printing set by the
	FS r command.
	The default is Normal (non half-width) printing.

Cancel DBCS Character Half Width and

Super/Subscript Printing

ASCII Code	FS DC2
Hex Code	28 12
Dec Code	1C 18
Purpose	This command cancels the FS SI (half-width DBCS character)
	and FS r (set super/subscript printing) commands.
Comment	The default is Normal (non half-width and non-super/subscript)
	printing.

Set Horizontal Tabs

ASCII Code ESC D n1 n2 … nk NUL

Hex Code 1B 44 n1 n2 … nk 00

Dec Code 27 68 n1 n2 … nk 00

Purpose Sets horizontal tab positions (in the current character pitch) at the columns specified by n1 to nk as measured from the left- margin position.

The values for n must be in ascending order; a value of n less than the previous n ends tab setting (like the NUL code).

Where:

0 <= k <= 32

1 <= n <= 255

nk > nk-1

Comment Changing the character pitch does not affect current tab settings.

Send an ESC D NUL command to cancel all tab settings.

The tab settings move to match any movement in the left margin.

68

Image 68

Contents Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Related Product Information Software FeaturesAbout This Manual Software Features Introduction Control PanelPrinting The Configuration Printing The ConfigurationPrinting Configurations Step Key Result Allows you to make configuration changesLocks the Enter key Configuration Menu Configuration Menu OverviewChanging Configurations Step Key Result Moving Within The Configuration MenuConfiguration Menu To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus MenuCPI/LPI Select Font Attributes Form Length Form WidthMargins Perforation SkipKssm Emulation Kssm EmulationDefine CR Code Kssm Emulation Exceptions And DifferencesDefault Values And States Factory Settings Characteristic Default SettingEscape Sequences FS SequencesConfiguring The Kssm Emulation With Control Codes Super-Set CommandsSet And Reset Codes Format For Control Code DescriptionsSetting the Page Format Setting the UnitsControl Code Index Control Code IndexMechanical Control Selecting CharactersControl-code Character Printing Data and Memory Control Hangul Extension CommandsPrinting Graphics Advance Print Position Vertically Align Sbcs Character with Dbcs CharacterCancel The Alignment of Sbcs Character With Dbcs Character Cancel The Alignment of Sbcs Character WithBackspace Ascii Code Hex Code Dec Code PurposeBarcode Printing Ascii Hex Selects BarcodeInch Barcode Printing Ascii Selects ValueOffset unit UPC-A UPC-E EAN Cancel Line BeeperCarriage Return BeeperDefine Pattern for Special Printing Effect Define User-Defined CharacterDefine User-Defined Chinese Character Delete Last Character in BufferDefine User-Defined Chinese Character Hex Code Dec CodeEnable Printing of Upper Control Codes Divided Hangul Double HeightFont Expansion Enable Upper Control CodesEnable Upper Control Codes Form Feed Graphic PrintingGraphics Printing Select Bit Image Graphics Printing Select Bit ImageInitialize Printer Line Feed Master Select Master SelectAscii Code ESC ! n Hex Code Bit On/Off Hex Dec Function EquivalentMaster Select In Dbcs Mode Ascii Code FS ! n Hex CodeMaster Select One-Line Attribute In Dbcs Mode Master Select One-Line Attribute In Dbcs ModePair Two Characters in Vertical Printing Bit On/Off Hex Dec FunctionSelect 1/8-inch Line Spacing Reassign Bit-image ModeSelect 1/6-inch Line Spacing Select 10 CPI Select 12 CPISelect 15 CPI Select 10 CPISelect 60-dpi Graphics Select 120-dpi GraphicsSelect 240-dpi Graphics Select 120-dpi GraphicsSelect an International Character Set USASelect Bit Image Select Bit ImageSelect Character Style Cancel Bold FontSelect Bold Font Select Character Table Select Condensed PrintingSelect Character Table Ascii Code ESC t n Hex CodeCancel Condensed Printing Cancel Double-strike Printing Select Dbcs Print QualitySelect Double-strike Printing Select Dbcs Print QualityCancel Double-width Printing One Line Select Double-width Printing One LineSelect Double-width Printing in Dbcs Mode One Select Double-width Printing in Dbcs Mode One LineCancel Double-width Printing in Dbcs Mode One Line Select Dbcs Mode Cancel Dbcs ModeSelect Hangul Myunjo/Gothic Style Ascii Code Hex CodeCancel Italic Font Select Italic FontSelect Print Quality Select Italic FontSelect Superscript/Subscript Printing Select PrinterDeselect Printer Cancel Superscript/Subscript Printing Cancel Superscript/Subscript PrintingSelect Dbcs Super/Subscript Printing Select Vertical PrintingSet n/180-inch Line Spacing Cancel Vertical Printing Select Horizontal PrintingSet n/60-inch Line Spacing Cancel Bottom Margin Set Absolute Horizontal Print PositionSet Bottom Margin Set Absolute Horizontal Print PositionCancel Dbcs Character Half Width Super/Subscript Printing Set Dbcs Character Half WidthSet Horizontal Tabs Ascii Code ESC D n1 n2 … nk NULSet Intercharacter Space Set Intercharacter SpaceSet Left Margin Set Page Length In Inches Set Page Length In InchesSet Page Length In Lines Set Relative Horizontal Print Position Set Right MarginSet Vertical Tab Channels Set Vertical TabsSet Vertical Tab Channels Ascii Code ESC B n1 n2 … nk NULDec Code 27 98 m n1 … nk Set Vertical Tabs In VFU ChannelsAscii Code ESC b m n1 … nk NUL Tab Horizontally Tab HorizontallyTab Vertically Turn Auto-wrap Around On/Off Turn Double-Height Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Double-Width, Double-Height Printing On/OffTurn Double-Width Printing On/Off Ascii Code Assc 0 z n Turn Extending Table Character On/OffTurn On/Off Ocrb Selection Turn Underline On/Off Turn Proportional Mode On/OffTurn Proportional Mode On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Code Table Korean Standard Code Table KSC5601Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Customer Support Center Printronix Supplies DepartmentCorporate Offices Appendix C Contact InformationIndex Page Page 100 Page 179981-001