Printronix P7000 H-Series, PSA3 About This Manual, Software Features, Related Product Information

Page 9

1 Introduction

About This Manual

This manual is designed so you can quickly find the information you need to operate your printer with the Korean Standard (KS) emulation.

This book does not explain how to operate the printer. For printer operation, see the User’s Manual.

Warnings And Special Information

Read and comply with all information highlighted under special headings:

WARNING Conditions that could harm you.

CAUTION Conditions that could damage the printer or related equipment. IMPORTANT Information vital to proper operation of the printer.

NOTE: Information affecting printer operation.

Related Product Information

Refer to the following book for printer operation:

•User’s Manual. Provides configuration instructions, descriptions, and troubleshooting guidelines. Also describes the keys on the control panel and provides quick reference information on daily printer operations such as loading paper and replacing ribbons.

Software Features

The KSSM emulation software provides the following features:

•Graphics and print quality. You can enable graphics mode and specify a density mode (dots per inch), for either 8-pin or 24-pin images.

•Print Attributes. Characters can be bold, italic, double high, double wide, etc.

•Page Formatting. Commands which allow you to set line spacing, page length, and vertical tabbing.

•Font Typefaces. Also referred to as print modes. The six typefaces are LQ, Near LQ, Normal, Hi-Speed, Super Hi-Speed, and Ultra Hi-Speed.

9

Image 9

Contents Programmer’s Reference Manual Page Page Trademark Acknowledgements Table Of Contents Table Of Contents Set Intercharacter Spacing of Dbcs Character Standard Ascii Character Set Code Table Software Features About This ManualRelated Product Information Software Features Control Panel IntroductionPrinting The Configuration Printing The ConfigurationAllows you to make configuration changes Printing Configurations Step Key ResultLocks the Enter key Configuration Menu Overview Configuration MenuMoving Within The Configuration Menu Configuration MenuChanging Configurations Step Key Result To USE Current Configuration Without Saving Saving Your New Configuration If you are already in the configuration menu, go to step Configuration Menu Saving Configurations Step Key Result LinePrinter Plus Menu LinePrinter Plus MenuCPI/LPI Select Font Attributes Form Width Form LengthMargins Perforation SkipKssm Emulation Kssm EmulationDefine CR Code Exceptions And Differences Kssm EmulationFactory Settings Characteristic Default Setting Default Values And StatesFS Sequences Escape SequencesSuper-Set Commands Configuring The Kssm Emulation With Control CodesSet And Reset Codes Format For Control Code DescriptionsSetting the Units Setting the Page FormatControl Code Index Control Code IndexSelecting Characters Control-code Character PrintingMechanical Control Hangul Extension Commands Printing GraphicsData and Memory Control Align Sbcs Character with Dbcs Character Advance Print Position VerticallyCancel The Alignment of Sbcs Character With Cancel The Alignment of Sbcs Character With Dbcs CharacterBackspace Ascii Code Hex Code Dec Code PurposeAscii Hex Selects Barcode Barcode PrintingBarcode Printing Ascii Selects Value Offset unitInch UPC-A UPC-E EAN Beeper Cancel LineCarriage Return BeeperDefine User-Defined Character Define Pattern for Special Printing EffectDelete Last Character in Buffer Define User-Defined Chinese CharacterDefine User-Defined Chinese Character Hex Code Dec CodeDivided Hangul Double Height Enable Printing of Upper Control CodesEnable Upper Control Codes Enable Upper Control CodesFont Expansion Graphic Printing Form FeedGraphics Printing Select Bit Image Initialize PrinterGraphics Printing Select Bit Image Line Feed Master Select Master SelectAscii Code ESC ! n Hex Code Bit On/Off Hex Dec Function EquivalentAscii Code FS ! n Hex Code Master Select In Dbcs ModeMaster Select One-Line Attribute In Dbcs Mode Master Select One-Line Attribute In Dbcs ModePair Two Characters in Vertical Printing Bit On/Off Hex Dec FunctionReassign Bit-image Mode Select 1/6-inch Line SpacingSelect 1/8-inch Line Spacing Select 12 CPI Select 10 CPISelect 15 CPI Select 10 CPISelect 120-dpi Graphics Select 60-dpi GraphicsSelect 120-dpi Graphics Select 240-dpi GraphicsUSA Select an International Character SetSelect Bit Image Select Bit ImageCancel Bold Font Select Bold FontSelect Character Style Select Condensed Printing Select Character TableSelect Character Table Ascii Code ESC t n Hex CodeCancel Condensed Printing Select Dbcs Print Quality Cancel Double-strike PrintingSelect Double-strike Printing Select Dbcs Print QualitySelect Double-width Printing One Line Cancel Double-width Printing One LineSelect Double-width Printing in Dbcs Mode One Line Cancel Double-width Printing in Dbcs Mode One LineSelect Double-width Printing in Dbcs Mode One Cancel Dbcs Mode Select Dbcs ModeSelect Hangul Myunjo/Gothic Style Ascii Code Hex CodeSelect Italic Font Cancel Italic FontSelect Print Quality Select Italic FontSelect Printer Deselect PrinterSelect Superscript/Subscript Printing Cancel Superscript/Subscript Printing Cancel Superscript/Subscript PrintingSelect Dbcs Super/Subscript Printing Select Vertical PrintingCancel Vertical Printing Select Horizontal Printing Set n/60-inch Line SpacingSet n/180-inch Line Spacing Set Absolute Horizontal Print Position Cancel Bottom MarginSet Bottom Margin Set Absolute Horizontal Print PositionSet Dbcs Character Half Width Cancel Dbcs Character Half Width Super/Subscript PrintingSet Horizontal Tabs Ascii Code ESC D n1 n2 … nk NULSet Intercharacter Space Set Intercharacter SpaceSet Left Margin Set Page Length In Inches Set Page Length In LinesSet Page Length In Inches Set Right Margin Set Relative Horizontal Print PositionSet Vertical Tabs Set Vertical Tab ChannelsSet Vertical Tab Channels Ascii Code ESC B n1 n2 … nk NULSet Vertical Tabs In VFU Channels Ascii Code ESC b m n1 … nk NULDec Code 27 98 m n1 … nk Tab Horizontally Tab VerticallyTab Horizontally Turn Double-Height Printing On/Off Turn Auto-wrap Around On/OffTurn Double-Width, Double-Height Printing On/Off Turn Double-Width Printing On/OffTurn Double-Width, Double-Height Printing On/Off Turn Extending Table Character On/Off Turn On/Off Ocrb SelectionAscii Code Assc 0 z n Turn Proportional Mode On/Off Turn Proportional Mode On/OffTurn Underline On/Off Turn Underline On/Off Hangul Extension Standard Ascii Character Set Appendix a Korean Standard Code Table KSC5601 Code TableAppendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Korean Standard Code Table KSC5601 Appendix B Code Table Printronix Supplies Department Printronix Customer Support CenterAppendix C Contact Information Corporate OfficesIndex Page Page 100 Page 179981-001