Printronix SL5000r manual Running Auto Calibrate

Page 31

Running Auto Calibrate

4.Press or until Label Length / 6 inch* displays (default).

5.Press + or until the value that matches the physical length of the installed media displays. See “Label Length” on page 42.

NOTE: Selecting the correct Label Length forces Auto Calibrate to increase media advancement for long labels (to detect actual gaps, notches, or marks) and decrease media advancement for short labels.

6.Press or until Gap/Mark Sensor / Disable* displays.

7.Press + or until Gap displays.

NOTE: If you are using smart labels, see “Gap Sensing for Smart Labels” on page 46.

8.Press . An asterisk (*) displays next to the selected item.

9.Press until Auto Calibrate / Run Calibrate displays.

10.Press . Media advances until it can accurately detect the label length indicators and then stops at the top-of-form position. The Sensed Distance value then displays for one second.

11.Auto Calibrate is successful when the Sensed Distance value correctly matches that of the installed media. For Gap sensing, the Sensed Distance value is the physical length of one label plus the length of one gap.

12.If GAP NOT DETECTED or PAPER OUT displays:

a.Check the horizontal position of the media sensors (page 28).

b.Make a Media Profile printout to verify that the sensors are performing properly (page 32).

c.Press PAUSE and run Auto Calibrate again.

13.Press the PAUSE key to take the printer offline.

14.Press the FEED key several times. Each time you press FEED, the media should advance one label length and stop.

15.Once the Sensed Distance value and performance is confirmed, save it to the desired configuration menu as described on page 50 before powering off the printer.

31

Image 31
Contents Quick Setup Guide Page Page Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesDeclaration Of Conformity CE Notice European UnionTrademark Acknowledgements Taiwan Lithium Battery WarningTable of Contents Table of Contents Unpacking The Printer Unpacking And Installing The PrinterRemoving The Internal Packing Material Unpacking And Installing The PrinterInstallation InstallationControl Panel Controls And IndicatorsPower Switch Controls And IndicatorsLiquid Crystal JOB Select Key Control Panel KeysControl Panel Down Key in Menu mode Menu KeyLoading Media And Ribbon Loading Media And RibbonLoading Roll Media Loading Roll MediaMedia Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Left Pressure Block Printing AdjustmentsPrinthead Pressure Adjustment Printhead Pressure Block AdjustmentsPositioning The Media Sensors Printing AdjustmentsFeed Positioning The Media SensorsRunning Auto Calibrate Calibrating The PrinterCalibrating The Printer Running Auto Calibrate Making a Media Profile Printout Making a Media Profile Printout Gap Sensing255 191 127 Advanced Gap Sensing Paper Out075 Changing The Active IGP Emulation Configuring The PrinterQuick Setup Menu Quick Setup MenuCont. from previous Print Speed Quick Setup Menu ItemsPrint Mode Print IntensityMedia Handling Quick Setup Menu ItemsVer Image Shift Paper Feed ShiftLabel Length Label WidthOrientation Hor Image ShiftEdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap Sensing for Smart Labels Gap/Mark SensorAuto Calibrate Validator Funct Save ConfigActive IGP Emul SMT Select Tool Power-Up ConfigSMT Status SMT Sel ToolsetAuto Save Configuration Saving The ConfigurationSaving The Configuration Loading a Saved Configuration Selecting The Power-Up ConfigurationPrinting a Configuration Printing a ConfigurationRun a Barcode Demo Test Exterior CleaningGeneral Cleaning Cleaning The Printhead, Platen Roller, Media SensorsCleaning The Printhead, Platen Roller, And Media Sensors Platen Roller CleaningMedia Sensor Cleaning Media Damper CleaningCleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The PrinterMedia Cover window side Straps not supplied Contact Information Contact InformationPrintronix Customer Support Center Printronix Supplies DepartmentCorporate Offices For More InformationCorporate Offices Page Page 178423-001