Printronix SL5000r manual Making a Media Profile Printout

Page 32

Calibrating The Printer

Making A Media Profile Printout

The Media Profile printout shows the relationship of the Paper Out Threshold and the Gap/Mark Threshold values, illustrates if and when each label length indicator is detected, and shows the difference between the label length indicators and the label. The profile printout (see figure on page 33) helps you set the thresholds for difficult media. This includes pre-printed labels, labels with poor gap/media dynamic range, and smart labels that have embedded RFID tags.

NOTE: Verify the CALIBRATE CTRL menu Gap/Mark Sensor option (Disable, Mark, Gap, Advanced Gap, or Advanced Notch) matches the installed media.

You will need a minimum installed label width of two inches to support the Media Profile printout.

Ensure the lower media sensor is horizontally positioned to permit sensing of the label length indicators. See “Positioning The Media Sensors” on page 28.

Ensure the Print Mode option selected in the QUICK SETUP menu matches the media installed. Select Direct for heat sensitive media (no ribbon required) or Transfer for thermal transfer media (ribbon required).

IMPORTANT Once Media Profile is initiated, the printer will continue to advance media and print the profile in landscape orientation until you press to stop printing.

.

1. Press the .. key to take the printer offline and into Menu mode.

2. Press and together until ENTER SWITCH / UNLOCKED displays.

.

3. Press .. until CALIBRATE CTRL displays.

4. Press until Media Profile / Profile Print displays and then press .

The printer will advance media and continue to print a dynamic profile image depicting the relationship of the label and any label length indicators detected.

5. Press to stop printing.

32

Image 32
Contents Quick Setup Guide Page Page Software License Agreement DefinitionsTermination of License Agreement Communication Notices CanadaCE Notice European Union Declaration Of ConformityTaiwan Lithium Battery Warning Trademark AcknowledgementsTable of Contents Table of Contents Unpacking And Installing The Printer Unpacking The PrinterUnpacking And Installing The Printer Removing The Internal Packing MaterialInstallation InstallationControls And Indicators Power SwitchControls And Indicators Control PanelLiquid Crystal Control Panel Keys JOB Select KeyDown Key in Menu mode Menu Key Control PanelLoading Media And Ribbon Loading Media And RibbonLoading Roll Media Loading Roll MediaMedia Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Printing Adjustments Printhead Pressure AdjustmentPrinthead Pressure Block Adjustments Left Pressure BlockPrinting Adjustments Positioning The Media SensorsPositioning The Media Sensors FeedCalibrating The Printer Calibrating The PrinterRunning Auto Calibrate Running Auto Calibrate Making a Media Profile Printout Gap Sensing Making a Media Profile Printout255 191 127 Advanced Gap Sensing Paper Out075 Configuring The Printer Changing The Active IGP EmulationQuick Setup Menu Quick Setup MenuCont. from previous Quick Setup Menu Items Print ModePrint Intensity Print SpeedQuick Setup Menu Items Media HandlingPaper Feed Shift Label LengthLabel Width Ver Image ShiftHor Image Shift OrientationEdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap/Mark Sensor Gap Sensing for Smart LabelsAuto Calibrate Active IGP Emul Save ConfigValidator Funct Power-Up Config SMT StatusSMT Sel Toolset SMT Select ToolSaving The Configuration Saving The ConfigurationAuto Save Configuration Selecting The Power-Up Configuration Loading a Saved ConfigurationPrinting a Configuration Printing a ConfigurationRun a Barcode Demo Test Cleaning General CleaningCleaning The Printhead, Platen Roller, Media Sensors ExteriorPlaten Roller Cleaning Media Sensor CleaningMedia Damper Cleaning Cleaning The Printhead, Platen Roller, And Media SensorsCleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The PrinterMedia Cover window side Straps not supplied Contact Information Printronix Customer Support CenterPrintronix Supplies Department Contact InformationCorporate Offices For More InformationCorporate Offices Page Page 178423-001