Printronix SL5000r manual Termination of License Agreement

Page 5

2.IN NO EVENT WILL PRINTRONIX, INC. BE LIABLE FOR LOST PROFITS, LOST DATA, BUSINESS INTERRUPTIONS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF PRINTRONIX, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR ANY DAMAGES CAUSED BY THE ABUSE OR MANIPULATION OF THE SOFTWARE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

3.Printronix, Inc. will not be liable for any loss or damage caused by delay in furnishing a Software Product or any other performance under this Agreement.

4.Our entire liability and your exclusive remedies for our liability of any kind (including liability for negligence except liability for personal injury caused solely by our negligence) for the Software Product covered by this Agreement and all other performance or nonperformance by us under or related to this Agreement are limited to the remedies specified by this Agreement.

5.California law governs this Agreement.

Termination of License Agreement

This License shall continue until terminated. This license may be terminated by agreement between you and Printronix, Inc. or by Printronix, Inc. if you fail to comply with the terms of this License and such failure is not corrected within thirty (30) days after notice. When this License is terminated, you shall return to the place you obtained them, the printer and all copies of the Software and documentation.

U.S. Government Restricted Rights

Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 242.227-7013, subdivision (b) (3) (ii) or subparagraph

(c)(1) (ii), as appropriate. Further use, duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52.227-19 (c) (2).

Acknowledgement of Terms and Conditions

YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT CONTAINED IN THIS AGREEMENT. NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY. BY USING THIS PRINTER, YOU AGREE TO ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT.

Image 5
Contents Quick Setup Guide Page Page Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesDeclaration Of Conformity CE Notice European UnionTrademark Acknowledgements Taiwan Lithium Battery WarningTable of Contents Table of Contents Unpacking The Printer Unpacking And Installing The PrinterRemoving The Internal Packing Material Unpacking And Installing The PrinterInstallation InstallationPower Switch Controls And IndicatorsControls And Indicators Control PanelLiquid Crystal JOB Select Key Control Panel KeysControl Panel Down Key in Menu mode Menu KeyLoading Media And Ribbon Loading Media And RibbonLoading Roll Media Loading Roll MediaMedia Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Printhead Pressure Adjustment Printing AdjustmentsPrinthead Pressure Block Adjustments Left Pressure BlockPositioning The Media Sensors Printing AdjustmentsFeed Positioning The Media SensorsCalibrating The Printer Calibrating The PrinterRunning Auto Calibrate Running Auto Calibrate Making a Media Profile Printout Making a Media Profile Printout Gap Sensing255 191 127 Advanced Gap Sensing Paper Out075 Changing The Active IGP Emulation Configuring The PrinterQuick Setup Menu Quick Setup MenuCont. from previous Print Mode Quick Setup Menu ItemsPrint Intensity Print SpeedMedia Handling Quick Setup Menu ItemsLabel Length Paper Feed ShiftLabel Width Ver Image ShiftOrientation Hor Image ShiftEdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap Sensing for Smart Labels Gap/Mark SensorAuto Calibrate Active IGP Emul Save ConfigValidator Funct SMT Status Power-Up ConfigSMT Sel Toolset SMT Select ToolSaving The Configuration Saving The ConfigurationAuto Save Configuration Loading a Saved Configuration Selecting The Power-Up ConfigurationPrinting a Configuration Printing a ConfigurationRun a Barcode Demo Test General Cleaning CleaningCleaning The Printhead, Platen Roller, Media Sensors ExteriorMedia Sensor Cleaning Platen Roller CleaningMedia Damper Cleaning Cleaning The Printhead, Platen Roller, And Media SensorsCleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The PrinterMedia Cover window side Straps not supplied Printronix Customer Support Center Contact InformationPrintronix Supplies Department Contact InformationCorporate Offices For More InformationCorporate Offices Page Page 178423-001