Printronix SL5000r manual Cont. from previous

Page 39

QUICK SETUP

(cont. from previous page)

Validator Funct. 1

Enable*

Disable

Active IGP Emul

Save Config.

IGP/PGL* PPI/ZGL PPI/TGL PPI/IGL PPI/STGL PPI/DGL IGP/VGL

	1*		1 to 8
	1*		1 to 8

Power-Up Config.

SMT: Status 2

SMT: Sel Toolset 2

Factory*

Disabled*

Toolset [1]*

1 to 8

Enabled

Toolset [1] to Toolset [4]

SMT: Select Tool 2, 3

EPC 4 zEPC 5

GTIN 4

zGTIN 5

	UPCA 4		EAN8 4
	zUPCA 5		zEAN8 5
	zUPCA 5		zEAN8 5
	Notes:
	* = Default.

EAN13 4

zEAN13 5

UCC128 4 zUCC128 5

1Appears only if an online data validator (validator) is installed.

2Appears only if an RFID encoder is installed.

3Undocumented options are reserved for internal use and future design.

4Appears only if Toolset [1] is selected under SMT: Sel Toolset.

5Appears only if Toolset [2] is selected under SMT: Sel Toolset.

NOTE: Many QUICK SETUP menu items are available in other main menus. (Refer to the User’s Manual.)

Changes made in the QUICK SETUP menu are updated in the other main menus, and vice versa.

39

Image 39

Contents Quick Setup Guide Page Page Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesDeclaration Of Conformity CE Notice European UnionTrademark Acknowledgements Taiwan Lithium Battery WarningTable of Contents Table of Contents Unpacking The Printer Unpacking And Installing The PrinterRemoving The Internal Packing Material Unpacking And Installing The PrinterInstallation InstallationControl Panel Controls And IndicatorsPower Switch Controls And IndicatorsLiquid Crystal JOB Select Key Control Panel KeysControl Panel Down Key in Menu mode Menu KeyLoading Media And Ribbon Loading Media And RibbonLoading Roll Media Loading Roll MediaMedia Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Left Pressure Block Printing AdjustmentsPrinthead Pressure Adjustment Printhead Pressure Block AdjustmentsPositioning The Media Sensors Printing AdjustmentsFeed Positioning The Media SensorsCalibrating The Printer Running Auto CalibrateCalibrating The Printer Running Auto Calibrate Making a Media Profile Printout Making a Media Profile Printout Gap Sensing255 191 127 Advanced Gap Sensing Paper Out075 Changing The Active IGP Emulation Configuring The PrinterQuick Setup Menu Quick Setup MenuCont. from previous Print Speed Quick Setup Menu ItemsPrint Mode Print IntensityMedia Handling Quick Setup Menu ItemsVer Image Shift Paper Feed ShiftLabel Length Label WidthOrientation Hor Image ShiftEdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap Sensing for Smart Labels Gap/Mark SensorAuto Calibrate Save Config Validator FunctActive IGP Emul SMT Select Tool Power-Up ConfigSMT Status SMT Sel ToolsetSaving The Configuration Auto Save ConfigurationSaving The Configuration Loading a Saved Configuration Selecting The Power-Up ConfigurationPrinting a Configuration Printing a ConfigurationRun a Barcode Demo Test Exterior CleaningGeneral Cleaning Cleaning The Printhead, Platen Roller, Media SensorsCleaning The Printhead, Platen Roller, And Media Sensors Platen Roller CleaningMedia Sensor Cleaning Media Damper CleaningCleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The PrinterMedia Cover window side Straps not supplied Contact Information Contact InformationPrintronix Customer Support Center Printronix Supplies DepartmentFor More Information Corporate OfficesCorporate Offices Page Page 178423-001