Printronix SL5000r manual Power-Up Config, SMT Status, SMT Sel Toolset, SMT Select Tool

Page 49

QUICK SETUP Menu Items

Power-Up Config.

You can specify the Factory configuration or any one of the eight possible saved configurations as the power-up configuration.

The default is Factory.

SMT: Status

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

Disabled.The printer disables the use of the Software Migration Tools.

Enabled. The printer enables the use of the Software Migration Tools.

SMT: Sel Toolset

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

Toolset [1]. SMTs for PGL emulation.

Toolset [2]. SMTs for PPI/ZGL emulation.

Toolset [3] and Toolset [4]. Reserved for internal use and future design.

SMT: Select Tool

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

EPC, GTIN, UPCA, EAN8, EAN13, and UCC128. SMTs displayed if Toolset [1] is selected under SMT: Sel Toolset.

zEPC, zGTIN, zUPCA, zEAN8, zEAN13, and zUCC128. SMTs displayed if Toolset [2] is selected under SMT: Sel Toolset.

NOTE: Undocumented options are reserved for internal use and future design.

49

Image 49
Contents Quick Setup Guide Page Page Definitions Software License AgreementTermination of License Agreement Canada Communication NoticesDeclaration Of Conformity CE Notice European UnionTrademark Acknowledgements Taiwan Lithium Battery WarningTable of Contents Table of Contents Unpacking The Printer Unpacking And Installing The PrinterRemoving The Internal Packing Material Unpacking And Installing The PrinterInstallation InstallationPower Switch Controls And IndicatorsControls And Indicators Control PanelLiquid Crystal JOB Select Key Control Panel KeysControl Panel Down Key in Menu mode Menu KeyLoading Media And Ribbon Loading Media And RibbonLoading Roll Media Loading Roll MediaMedia Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Printhead Pressure Adjustment Printing AdjustmentsPrinthead Pressure Block Adjustments Left Pressure BlockPositioning The Media Sensors Printing AdjustmentsFeed Positioning The Media SensorsRunning Auto Calibrate Calibrating The PrinterCalibrating The Printer Running Auto Calibrate Making a Media Profile Printout Making a Media Profile Printout Gap Sensing255 191 127 Advanced Gap Sensing Paper Out075 Changing The Active IGP Emulation Configuring The PrinterQuick Setup Menu Quick Setup MenuCont. from previous Print Mode Quick Setup Menu ItemsPrint Intensity Print SpeedMedia Handling Quick Setup Menu ItemsLabel Length Paper Feed ShiftLabel Width Ver Image ShiftOrientation Hor Image ShiftEdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap Sensing for Smart Labels Gap/Mark SensorAuto Calibrate Validator Funct Save ConfigActive IGP Emul SMT Status Power-Up ConfigSMT Sel Toolset SMT Select ToolAuto Save Configuration Saving The ConfigurationSaving The Configuration Loading a Saved Configuration Selecting The Power-Up ConfigurationPrinting a Configuration Printing a ConfigurationRun a Barcode Demo Test General Cleaning CleaningCleaning The Printhead, Platen Roller, Media Sensors ExteriorMedia Sensor Cleaning Platen Roller CleaningMedia Damper Cleaning Cleaning The Printhead, Platen Roller, And Media SensorsCleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The PrinterMedia Cover window side Straps not supplied Printronix Customer Support Center Contact InformationPrintronix Supplies Department Contact InformationCorporate Offices For More InformationCorporate Offices Page Page 178423-001