Ultimate Technology 500 POS manual LED Turns on

Page 29

Table 3. Local Mode Programming Instructions - Continued

Note: *Default Settings

Function Code(s)

Operation

Normal Indication

Remarks

 

 

 

 

Note:

Disabling all format tracks will not disable the secure or

 

programming operations.

 

09

1. While in programming mode, at the Series 500 Keyboard numeric

Magnetic Stripe

keypad, enter Function code 09.

Reader (MSR)

 

 

Beeper

LED (2)

turns on.

 

2. At Series 500 Keyboard numeric keypad, enter the applicable

 

number (1 through 4) to select magnetic stripe reader beeper

 

operation per list below.

 

1

= beep on good read for all enabled tracks

 

2

= beep on bad read for all enabled tracks

 

3

= beep on good or bad read of enabled tracks*

 

4

= no beep on good or bad reads

 

LED (2)

turns off.

 

3. Program the next function code or exit the local programming mode

 

by entering 99 on Series 500 Keyboard numeric keypad followed by

 

ENTER or by swiping the Programmer's card. If using the optional

 

3- position keyswitch, move switch out of the AUX position.

 

 

10

1. While in programming mode, at the Series 500 Keyboard numeric

11

keypad, enter applicable Function Code 10, 11, 12 or 13.

12

 

 

13

LED (2)

flashes.

Magnetic Stripe

 

 

Reader (MSR)

2. At the auxiliary keyboard, press the desired key or type the desired

Channel 1,3

key sequence. Note that the maximum number of key codes that

Prefix (10)

can be entered is limited to 24 - this is the equivalent to

Field

approximately 12 key strokes.

 

 

Separator (11)

 

If the Series 500 Keyboard

 

 

beeps and LED (2) turns off

Suffix (12)

 

while entering key codes at

 

 

the auxiliary keyboard, you

Account

 

have exceeded 24 key codes.

Separator (13)

 

Repeat steps 1 and 2.

 

3. At the Series 500 Keyboard, press ENTER.

 

LED (2)

turns off.

 

4. Program the next function code or exit programming mode by

 

entering 99 on Series 500 Keyboard numeric keypad or by swiping

 

 

21

 

 

 

Image 29
Contents Programming & USER’S Guide Series 500 Quick Reference Guide To Program a Primary KeyTable of Contents Maintenance List of Tables Series 500 POS Keyboard Ultimate Technology Corporation ScopeSpecial Note Series 500 POS Keyboard Model Description FeaturesProduct Information Optional Pedestal Mount Specifications Service and WarrantyUnpacking and Inspection InstallationDrawer Jumper Connections Printer Fired External ConnectionsCAB20138 Typical keyboard external connections Keyboard external connectors rear view Operation Controls and IndicatorsPage Page Programming Keyboard Operating Parameters Local Mode Programming Function Codes and Default SettingsProgramming MSR Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Instructions Local Mode Programming Instructions LED 2 turns on LED Turns on Move switch out of the AUX position 20 or 21 or 23 or 25 or O r D 2 f l a s h e s Applicable Function Code 45, 46, 47 or Indicator LED Code Mode LED 2 flashes Select override secure mode of operation per list below Default Keyboard Code Break Series Keyboard Description Numeric Keypad noPage Page Programming in Remote Mode Page Acknowledgement None Command A0krcCxDx.......CRCode HEX Command A1aCxDx.......CRCommand A2CxDxCR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEX SnddlyCommand A4xxxx-xxxxCR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEXCommand A3PbbbbbwsphCR Command A6xCR Command A5xCxDxCRCommand A7hhhmCR ClickedSecure Nvbdclr Command A9CLRCRRawed Light Command AFxxxx-xxxxCRCommand B0LxCR Command B1pdCR Command B3CR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEX SendpCommand B2p...........CR Reset Command B5RSTCR Command B4CRKssnd Command B6CR Ksstatus Command B7CRCarded Command B8xCRCommand B9cCR Cdcont Command BApCRCommand BBpCR Command BDpxCR Command BCpCRAcknowledgement PorteGetset Command Bfcr Command BecrBEnnnnnvvvvkkkkx-xCR BF...............CRProgramming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Parameters same as shown for example Keyboard downloading connection diagram Copying Keyboard Setup Data CloningSystem LOG Operators and Programmers Magnetic CardsPrecautions MaintenanceCleaning KEY Legend Change 5/8-INCH Full Travel KeyboardsKEY Legend Change Flat Tactile Membrane Battery ReplacementPage Appendix a Series 500 POS Standard Keyboard Layouts Page Compact 5/8-Inch Qwerty Layout Back Connector Pinouts Adapter Cable Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 Ultimate Technology Corporation One Year Limited Service Warranty Terms & ConditionsRawson Road VICTOR, NEW York