Ultimate Technology 500 POS manual Scope, Special Note, Ultimate Technology Corporation

Page 7

SCOPE

This user's guide provides the information and procedures needed to install, operate and program your Series 500 POS Keyboard. Differences in models and optional features are described in this manual, where applicable. It is suggested that the entire manual be read before attempting installation or programming. If assistance is needed that is beyond the coverage provided in this guide, please contact Customer Service:

Ultimate Technology Corporation

100 Rawson Road

Victor New York, 14564

Phone: (800) 349-0546

Fax: (585) 924-1434

SPECIAL NOTE

When this publication was written, every effort was made to ensure that information in this document was complete, accurate, and up to date. Ultimate Technology Corporation assumes no responsibility for errors beyond its control. Ultimate Technology Corporation also cannot guarantee that changes in software and equipment made by other manufacturers, and referenced in this guide, do not effect the applicability of the information in this manual. If assistance is needed, please contact Customer Service at the address or phone number given above.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT OPEN KEYBOARD ENCLOSURE WHEN

KEYBOARD IS CONNECTED TO SYSTEM.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE KEYBOARD TO RAIN OR MOISTURE.

Contents of this publication may be changed without notice and shall not be regarded as a warranty.

Series 500 POS Keyboard

Image 7
Contents Programming & USER’S Guide Series 500 Quick Reference Guide To Program a Primary KeyTable of Contents Maintenance List of Tables Series 500 POS Keyboard Special Note ScopeUltimate Technology Corporation Series 500 POS Keyboard Product Information FeaturesModel Description Optional Pedestal Mount Specifications Service and WarrantyUnpacking and Inspection InstallationDrawer Jumper Connections Printer Fired External ConnectionsCAB20138 Typical keyboard external connections Keyboard external connectors rear view Operation Controls and IndicatorsPage Page Programming Local Mode Programming Function Codes and Default SettingsProgramming Keyboard Operating Parameters MSR Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Function Codes and Default Settings Local Mode Programming Instructions Local Mode Programming Instructions LED 2 turns on LED Turns on Move switch out of the AUX position 20 or 21 or 23 or 25 or O r D 2 f l a s h e s Applicable Function Code 45, 46, 47 or Indicator LED Code Mode LED 2 flashes Select override secure mode of operation per list below Default Keyboard Code Break Series Keyboard Description Numeric Keypad noPage Page Programming in Remote Mode Page Acknowledgement None Command A0krcCxDx.......CRCode HEX Command A1aCxDx.......CRCommand A2CxDxCR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEX SnddlyCommand A3PbbbbbwsphCR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEXCommand A4xxxx-xxxxCR Clicked Command A5xCxDxCRCommand A6xCR Command A7hhhmCRRawed Nvbdclr Command A9CLRCRSecure Command B0LxCR Command AFxxxx-xxxxCRLight Command B1pdCR Command B2p...........CR MNEMONIC/DESCRIPTION COMMAND/ACKNOWLEDGEMENT Code HEX SendpCommand B3CR Ksstatus Command B7CR Command B4CRReset Command B5RSTCR Kssnd Command B6CRCommand B9cCR Command B8xCRCarded Command BBpCR Command BApCRCdcont Porte Command BCpCRCommand BDpxCR AcknowledgementBF...............CR Command BecrGetset Command Bfcr BEnnnnnvvvvkkkkx-xCRProgramming KEY MAKE/BREAK Codes Remote Description Programming CommandExamples of Remote Programming for KEY MAKE/BREAK Code Where A0Example Parameters same as shown for example Keyboard downloading connection diagram Copying Keyboard Setup Data CloningSystem LOG Operators and Programmers Magnetic CardsKEY Legend Change 5/8-INCH Full Travel Keyboards MaintenancePrecautions CleaningKEY Legend Change Flat Tactile Membrane Battery ReplacementPage Appendix a Series 500 POS Standard Keyboard Layouts Page Compact 5/8-Inch Qwerty Layout Back Connector Pinouts Adapter Cable Pinouts Appendix B Keyboard CABLE/CONNECTOR DataDLE Appendix C Ascii Character SETDecimal Hexadecimal Scan Code KEY Number2B/AB Scan Code KEY Number 4F/CF 3B/BB E1 14 77 E1 62/F0 9D C5 F0 14 F0 VICTOR, NEW York One Year Limited Service Warranty Terms & ConditionsUltimate Technology Corporation Rawson Road