Trango Broadband TrangoLink-10 user manual Same as updateflash

Command Set Summary

Command	Description	OFF	ON	Remark
ru reboot	reboot Remote Radio		se
ru speedtest [<packet length>	perform speedtest		se	default:
<file size>]	<pkt len> = 64..1760 bytes			<pkt len> = 1760 bytes
	<file size> = 10..100 Mbytes			<file size> = 10 MBytes
ru sysinfo	request Remote’s system information		se
ru testrflink [<packet length>]	perform RF loopback test testrflink		se	default:
	<pkt len> = 64..1760 bytes			<pkt len> = 1760 bytes
reboot	reboot unit	se	se
remarks [<str>]	string length should be 1 to 28 characters	se	se
reset [<all 0…n>]…	reset radio to the firmware default	se
	n# = 0..2
	Master:
	0 - Channel Table, Active Channel = 1 h,
	Switches, and Remarks
	1 - TX Power = Max, RF Threshold = -90
	dBm, Target RSSI = -60 dBm, MIR
	Downstream = 10000 kbps, Upstream =
	10000 kbps
	2 - SNMP Community String (Read/Write)
	= (public/private)
	Remote:
	0 - Channel Table, Active Channel = 1 h,
	Switches, and Remarks
	1 - TX Power = Max, RF Threshold = -90
	dBm
	2 - SNMP Community String (Read/Write)
	= (public/private)
rfrxth <ism> <-90 -85 -80 -	specify RF RX Threshold	se	se	default = -90 for both
75 -70 -65>				band
rfrxthreshold …	same as “rfrxth”	se	se
rssi	display current RX RSSI	se
save	same as “updateflash”	se	se
save mm	same as “updateflash mainimage”	se	se
save ss	same as “updateflash systemsetting”	se	se
set defaultopmode [<on off>]	set or display default Opmode	se	se
set httpport [<port #>]	set or display HTTPD port number	se	se	default = 80
set mir [<downstream,	set or display MIR	se	se
kbps>][<upstream, kbps>]	<kps> = 100..10000
set rssitarget <dB>	set Target RSSI Threshold	se	se
	It must be -45 to –75, and +5 dB higher
	than RF RX Threshold.
set snmpcomm [<read write>]	display or assign SNMP community string	se	se
set telnetport [<port #>]	specify telnet port, <port #> = 1..65534	se	se	default = 23
ssrssi <ch #> <v h>	display RSSI on the current channel	se
survey <ism> <time, sec> <hv>	spectrum analysis of entire RF band	se
sw 0 [<on off>]	set sw #0 – packet filter for	se	se	default = on
	broadcast/multicast
sw 1 [<on off>]	set sw #1 – HTTPD service	se	se	default = on
sw 2 [<on off>]	set sw #2 – Auto scan Master signal	se	se	default = on
sw 3 [<on off>]	set sw #3 – Auto power leveling Remote	se	se	default = on
	Unit
sysinfo	display system configuration	se	se
temp	display current temperature	se	se
Trango Broadband Wireless — TrangoLINK-10 User Manual Rev. E 3.0				page 27