Telit Wireless Solutions GE863-QUAD, GE863-PY manual GM863-GPS

Page 31

GE863-QUAD

GE863-PY

1vv0300715 Rev. 1 - 19/09/06

	8				audio2.skd
12dBFS 16	EXTERNAL		16
-	EXTERNAL
	AMPLIFIER
Differential Line-OutDrivers		FullyDifferential PowerBuffers		Balanced	Single ended
GM863-GPS	EarMT+	MicMT-EarMT-	EarHF+		EarHF-
GM863-GPS	Mic MT+	MicMT-EarMT-	Mic HF+	Mic HF-
		rms	rms
		365mV	23mV		Paths
					Audio
		+20dB	+10dB
		3,3mVrms	0,33mV rms
		-45dBV/Pa	-45dBV/Pa
		7cm
			50cm

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved

page 31 of 79

Image 31

Contents GE863-QUAD GE863-PY Hardware User Guide Contents 10.4 10.110.2 10.313.1 12.113.2 This document is relating to the following products Overview PIN-OUT GE863 module connectionsPin Signal Function Internal Type Pull up Pin Signal Function Internal Type Pins Layout Turning on the GE863-QUAD/PY Hardware CommandsTurning off of the device can be done in two ways Turning OFF the GE863-QUAD/PYHardware shutdown Hardware Unconditional RebootGE863-QUAD 1Power Supply Requirements Power SupplyGE863-QUAD/PY power requirements are Electrical design Guidelines 2General Design RulesAn example of linear regulator with 5V input is 1.2 + 12V input Source Power Supply Design GuidelinesAn example of switching regulator with 12V input is Battery Source Power Supply Design GuidelinesBattery Charge control Circuitry Design Guidelines Thermal Design Guidelines Power Supply PCB layout Guidelines GSM Antenna Requirements AntennaSerial Ports GSM Antenna installation GuidelinesGSM Antenna PCB line Guidelines Level Min Max Absolute Maximum Ratings -Not Functional Parameter Min MaxClear to Send Output from the GE863-QUAD/PY that Signals in the Uart connector on the EVK areNumber Pad Number 17-28-36 Ground 45-48-50-562MODEM Serial Port 2 Python Debug It is available on the following pins3RS232 level translation An example of level translation circuitry of this kind is 5V Uart level translation GE863-QUAD Audio Section Overview GM863-GPS + 20dB Microphone Paths Characteristic and RequirementsEcho canceller type Handset Echo canceller type Car kit hands-freeYou can set GA= +20dB to use standard resistor values That meansTIP environment consideration Other considerations General Design RulesBalanced Microphone Biasing Microphone BiasingUnbalanced Microphone Biasing GE863-QUAD Buffered Balanced Mic Microphone BufferingSample circuit can be Buffer gain is given by the formula Gain = RR604605 = RR607606Buffered Unbalanced Single Ended Microphone Buffer bandwidth at -3dB shall be 4KHz Freq . = 2π * R719* C726 2π * R711* C727GE863-QUAD Short description Output Lines SpeakerSW volume level step Number of SW volume steps Output Lines CharacteristicsNoise Filtering Handset Earphone Design An example of internal Ear amplifier could be Hands-Free Earphone Low Power DesignCar Kit Speakerphone Design Short Description Evaluation Kit for Telit Modules EVK2@ 350mW 2 EVK2 Audio Lines CharacteristicsESD Data IntegritySIM Supply SchematicLayout Using a Gpio Pad as Output Using a Gpio Pad as InputGeneral Purpose I/O Using the Buzzer Output GPIO7 10.3Using the Alarm Output GPIO6Min Max Units DAC and ADC section11.1DAC Converter DescriptionLow Pass Filter Example An AT command is available to use the DAC functionCommand is AT#DAC=enable,value Enabling DACInput Voltage range AD conversion Bits Resolution Using ADC Converter11.2ADC Converter Sensitivity Lux Camera12.1Transchip Camera TypeCamera Interface Connectors Camera Physical Detail & Connector Camera Socket Connector Camera Board Module Main Block Diagram for supported cameras Schematic Diagrams for supported camera Example usage script for camera Camera setting shown here are the defaults onesTaking an reading a photo Mounting the GE863-QUAD / PY on the Application Board 13.2Module Finishing & Dimensions13.1General Lead-free Alloy Surface finishing Ni/Au for all test padsRecommended foot print for the application Stencil Debug of the GE863 in ProductionPCB pad Design Solder paste Following is the recommended solder reflow profile 13.2.6 GE863-QUAD / PY Solder ReflowGE863-QUAD Section A-A Packing SystemModules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations 19/09/06 Document Change LogRevision Date Changes 21/02/06