Telit Wireless Solutions GE863-PY, GE863-QUAD manual Safety Recommandations

Page 78

GE863-QUAD

GE863-PY

1vv0300715 Rev. 1 - 19/09/06

15 SAFETY RECOMMANDATIONS

READ CAREFULLY

Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas:

Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc

Where there is risk of explosion such as gasoline stations, oil refineries, etc

It is responsibility of the user to enforce the country regulation and the specific environment regulation.

Do not disassemble the product; any mark of tampering will compromise the warranty validity.

We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations.

The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode.

The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force.

Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation.

The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information’s are available on the European Community website:

http://europa.eu.int/comm/enterprise/rtte/dir99-5.htm

The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at:

http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm

Reproduction forbidden without Telit Communications S.p.A. written authorization - All Right reserved

page 78 of 79

Image 78
Contents GE863-QUAD GE863-PY Hardware User Guide Contents 10.3 10.110.2 10.412.1 13.113.2 This document is relating to the following products Overview GE863 module connections PIN-OUTPin Signal Function Internal Type Pull up Pin Signal Function Internal Type Pins Layout Hardware Commands Turning on the GE863-QUAD/PYTurning OFF the GE863-QUAD/PY Turning off of the device can be done in two waysHardware Unconditional Reboot Hardware shutdownGE863-QUAD Power Supply 1Power Supply RequirementsGE863-QUAD/PY power requirements are 2General Design Rules Electrical design Guidelines1.2 + 12V input Source Power Supply Design Guidelines An example of linear regulator with 5V input isBattery Source Power Supply Design Guidelines An example of switching regulator with 12V input isBattery Charge control Circuitry Design Guidelines Thermal Design Guidelines Power Supply PCB layout Guidelines Antenna GSM Antenna RequirementsGSM Antenna installation Guidelines Serial PortsGSM Antenna PCB line Guidelines Absolute Maximum Ratings -Not Functional Parameter Min Max Level Min Max17-28-36 Ground 45-48-50-56 Signals in the Uart connector on the EVK areNumber Pad Number Clear to Send Output from the GE863-QUAD/PY thatIt is available on the following pins 2MODEM Serial Port 2 Python Debug3RS232 level translation An example of level translation circuitry of this kind is 5V Uart level translation GE863-QUAD Audio Section Overview GM863-GPS Echo canceller type Car kit hands-free Microphone Paths Characteristic and RequirementsEcho canceller type Handset + 20dBThat means You can set GA= +20dB to use standard resistor valuesTIP environment consideration General Design Rules Other considerationsMicrophone Biasing Balanced Microphone BiasingUnbalanced Microphone Biasing GE863-QUAD Microphone Buffering Buffered Balanced MicSample circuit can be Gain = RR604605 = RR607606 Buffer gain is given by the formulaBuffered Unbalanced Single Ended Microphone Freq . = 2π * R719* C726 2π * R711* C727 Buffer bandwidth at -3dB shall be 4KHzGE863-QUAD Output Lines Speaker Short descriptionOutput Lines Characteristics SW volume level step Number of SW volume stepsNoise Filtering Handset Earphone Design Hands-Free Earphone Low Power Design An example of internal Ear amplifier could beCar Kit Speakerphone Design Evaluation Kit for Telit Modules EVK2 Short Description2 EVK2 Audio Lines Characteristics @ 350mWData Integrity ESDSchematic SIM SupplyLayout Using a Gpio Pad as Input Using a Gpio Pad as OutputGeneral Purpose I/O 10.3Using the Alarm Output GPIO6 Using the Buzzer Output GPIO7Description DAC and ADC section11.1DAC Converter Min Max UnitsEnabling DAC An AT command is available to use the DAC functionCommand is AT#DAC=enable,value Low Pass Filter ExampleUsing ADC Converter Input Voltage range AD conversion Bits Resolution11.2ADC Converter Type Camera12.1Transchip Camera Sensitivity LuxCamera Interface Connectors Camera Physical Detail & Connector Camera Socket Connector Camera Board Module Main Block Diagram for supported cameras Schematic Diagrams for supported camera Camera setting shown here are the defaults ones Example usage script for cameraTaking an reading a photo 13.2Module Finishing & Dimensions Mounting the GE863-QUAD / PY on the Application Board13.1General Surface finishing Ni/Au for all test pads Lead-free AlloyRecommended foot print for the application Debug of the GE863 in Production StencilPCB pad Design Solder paste 13.2.6 GE863-QUAD / PY Solder Reflow Following is the recommended solder reflow profileGE863-QUAD Packing System Section A-AModules orientation on tray Moisture Sensibility Conformity Assessment Issues Safety Recommandations 21/02/06 Document Change LogRevision Date Changes 19/09/06