Synopsys 640-pin Generic Device Adapter manual Connector Pin Detail, Connectors J1 and J3

Page 13

The ModelSource 640-pin Adapter

Chapter 2: Building the Daughterboard

Connector Pin Detail

Connectors J1–J6 include the connections (DUT1–DUT640) between the DUT and the Adapter through the Daughterboard and, in addition, supply voltage, ground connections, and various auxiliary signals. Figure 2 shows details of J1–J6 connector pins, from the component side. Pinouts are listed in “J1–J6 Connector Pinouts” on page 29.

Connectors J1 and J3

These connectors include two each of Teradyne signal modules, and have 6 rows of 48 pins each. You will notice in Appendix A that no connections are listed for Rows B and E; these are exclusively ground.

Connectors J2, J4, J5 and J6

These connectors include one each of Teradyne signal modules (A1–F24, at the left of the figure) and two each of Teradyne power modules (AP1–FP4 and AP5–FP8, at the right of the figure). As with connectors J1 and J3, the left (signal module) side has rows B and E exclusively connected to ground. The right (power module) side has no rows B, C, or E.

November 2001

Synopsys, Inc.

13

Image 13
Contents Using the ModelSource Pin Generic Device Adapter ModelSource 640-pin Adapter Contents Appendix a J1-J6 Connector Pinouts About This Application Note PrefaceTypographical and Symbol Conventions Pin1 pin2 ... pinN Getting HelpDoc@synopsys.com Comments?Hardware Requirements Describing a 640-pin Logic ModelProcedural Summary Software RequirementsDaughterboard Description Building the Daughterboard640-pin Adapter Daughterboard Connectors J1 and J3 Connector Pin DetailConnector Pin Detail, Shown from Component Side Parts ListShows a drawing of the short and long board stiffeners RequirementsJ1-D17 Keepalive Routing GuidelinesADJVCC1 P5VADJVCC2 M5VPage Adapter Description Connecting the Daughterboard640-pin Generic Device Adapter Procedures Page User-Generated Files Developing the Shell SoftwareFiles Provided by Synopsys Partial GEN640.PKG File Mounting the Adapter onto the ModelSource Modeling Systems Completing the ModelVerifying the Model Labeling the DaughterboardUnmounting the Adapter from the ModelSource Modeling Systems Page SEAT1 J1-J6 Connector PinoutsTrigger Play SampleTemp Pinouts for Connectors J1-J6 DUT13 DUT11DUT10 DUT9DUT37 DUT38DUT36 DUT42DUT54 DUT55DUT53 DUT12DUT35 DUT41DUT43 DUT44SEAT2 DUT80Pinouts for Connectors J1-J6 DUT93 DUT91DUT90 DUT89DUT94 DUT92DUT95 DUT96FP7 FP6FP8 SEAT3DUT640 Reserved AD7 Reserved AD13Reserved AD5 Reserved AD0DUT615 Reserved AD12 Reserved AD11Reserved AD6 Reserved AD2Reserved AD10 Reserved AD3 Reserved AD9Reserved AD4 Reserved -RDReserved AD8 Reserved AD14Reserved AD1 Reserved -AS Reserved AD15SEAT4 DUT553 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT4 DUT400 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT5 FP1 Reserved FP2 FP3 FP4 FP5 FP6 FP7 FP8 SEAT6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 F20 DUT285 F21 DUT286 F22 F23 F24 FP5 Reserved FP6 FP7 FP8