Synopsys 640-pin Generic Device Adapter manual Labeling the Daughterboard, Verifying the Model

Page 26

Chapter 5: Completing the Model

The ModelSource 640-pin Adapter

Labeling the Daughterboard

After you have completed the Shell Software and mounted the Adapter and Daughterboard onto the ModelSource modeling systems, you must verify the Daughterboard’s label and update it if necessary.

Note

Ensure that the Daughterboard is seated on the Adapter before you verify and update the label. If the daughterboard is not seated, the software will report the label as “GEN640”, the label of the Adapter itself.

If it is necessary to update the Daughterboard’s label, use the lm Label Device Adapter utility to change the adapter’s label to the device_name used in the model’s Shell Software. For more details, refer to “Label Device Adapter“ in the ModelSource User’s Manual.

Verifying the Model

After you have developed the model, you must verify it. For more information, see the ModelSource User’s Manual and the Logic Model Development Manual.

Note

The pattern memory available for simulation is limited to the smallest amount of available memory on any one of the eight modeling boards in the four modelers.

26

Synopsys, Inc.

November 2001

Image 26
Contents Using the ModelSource Pin Generic Device Adapter ModelSource 640-pin Adapter Contents Appendix a J1-J6 Connector Pinouts Preface About This Application NoteTypographical and Symbol Conventions Getting Help Pin1 pin2 ... pinNComments? Doc@synopsys.comDescribing a 640-pin Logic Model Hardware RequirementsSoftware Requirements Procedural SummaryBuilding the Daughterboard Daughterboard Description640-pin Adapter Daughterboard Connector Pin Detail Connectors J1 and J3Parts List Connector Pin Detail, Shown from Component SideRequirements Shows a drawing of the short and long board stiffenersRouting Guidelines J1-D17 KeepaliveADJVCC2 P5VADJVCC1 M5VPage Connecting the Daughterboard Adapter Description640-pin Generic Device Adapter Procedures Page Files Provided by Synopsys Developing the Shell SoftwareUser-Generated Files Partial GEN640.PKG File Completing the Model Mounting the Adapter onto the ModelSource Modeling SystemsLabeling the Daughterboard Verifying the ModelUnmounting the Adapter from the ModelSource Modeling Systems Page Trigger J1-J6 Connector PinoutsSEAT1 Sample PlayTemp Pinouts for Connectors J1-J6 DUT10 DUT11DUT13 DUT9DUT36 DUT38DUT37 DUT42DUT53 DUT55DUT54 DUT12DUT43 DUT41DUT35 DUT44DUT80 SEAT2Pinouts for Connectors J1-J6 DUT90 DUT91DUT93 DUT89DUT95 DUT92DUT94 DUT96FP8 FP6FP7 SEAT3DUT640 Reserved AD5 Reserved AD13Reserved AD7 Reserved AD0DUT615 Reserved AD6 Reserved AD11Reserved AD12 Reserved AD2Reserved AD10 Reserved AD4 Reserved AD9Reserved AD3 Reserved -RDReserved AD1 Reserved AD14Reserved AD8 SEAT4 Reserved AD15Reserved -AS DUT553 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT4 DUT400 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT5 FP1 Reserved FP2 FP3 FP4 FP5 FP6 FP7 FP8 SEAT6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 F20 DUT285 F21 DUT286 F22 F23 F24 FP5 Reserved FP6 FP7 FP8