Synopsys 640-pin Generic Device Adapter manual Parts List

Page 14

Chapter 2: Building the Daughterboard

The ModelSource 640-pin Adapter

Connectors J1 and J3

 

One Teradyne

One Teradyne

 

Signal Module

Signal Module

1

24

48

A

B

C

D

E

F

Rows B and E are connected to ground

Connectors J2, J4, J5 and J6

 

 

One Teradyne

Two Teradyne

Signal Module

Power Modules

1

24

AP8

 

AP1

A

 

 

B

DP1

DP8

C

D

 

 

E

 

 

F

FP1

FP8

 

Rows B and E are

Rows B, C, and E

connected to ground

 

do not exist

Figure 2: Connector Pin Detail, Shown from Component Side

Parts List

The required parts are as follows:

Eight Teradyne HDM signal modules, 488-5324-XXX. These are available either as press fit or solder tail, in a variety of tail lengths. The last three digits (XXX) of the part number depend on which type you choose; for specific part numbers, see the Teradyne product documentation.

Eight Teradyne HDM power modules, 437-5034-500. These are currently available only as solder tail.

Twelve Southco retractable screw fasteners, 47-65-221-70.

To mount the stiffeners:

Fourteen 4-40 1/4” pan head Phillips screws

14

Synopsys, Inc.

November 2001

Image 14
Contents Using the ModelSource Pin Generic Device Adapter ModelSource 640-pin Adapter Contents Appendix a J1-J6 Connector Pinouts Preface About This Application NoteTypographical and Symbol Conventions Getting Help Pin1 pin2 ... pinNComments? Doc@synopsys.comDescribing a 640-pin Logic Model Hardware RequirementsSoftware Requirements Procedural SummaryBuilding the Daughterboard Daughterboard Description640-pin Adapter Daughterboard Connector Pin Detail Connectors J1 and J3Parts List Connector Pin Detail, Shown from Component SideRequirements Shows a drawing of the short and long board stiffenersRouting Guidelines J1-D17 KeepaliveADJVCC2 P5VADJVCC1 M5VPage Connecting the Daughterboard Adapter Description640-pin Generic Device Adapter Procedures Page Files Provided by Synopsys Developing the Shell SoftwareUser-Generated Files Partial GEN640.PKG File Completing the Model Mounting the Adapter onto the ModelSource Modeling SystemsLabeling the Daughterboard Verifying the ModelUnmounting the Adapter from the ModelSource Modeling Systems Page Trigger J1-J6 Connector PinoutsSEAT1 Sample PlayTemp Pinouts for Connectors J1-J6 DUT10 DUT11DUT13 DUT9DUT36 DUT38DUT37 DUT42DUT53 DUT55DUT54 DUT12DUT43 DUT41DUT35 DUT44DUT80 SEAT2Pinouts for Connectors J1-J6 DUT90 DUT91DUT93 DUT89DUT95 DUT92DUT94 DUT96FP8 FP6FP7 SEAT3DUT640 Reserved AD5 Reserved AD13Reserved AD7 Reserved AD0DUT615 Reserved AD6 Reserved AD11Reserved AD12 Reserved AD2Reserved AD10 Reserved AD4 Reserved AD9Reserved AD3 Reserved -RDReserved AD1 Reserved AD14Reserved AD8 SEAT4 Reserved AD15Reserved -AS DUT553 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT4 DUT400 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 SEAT5 FP1 Reserved FP2 FP3 FP4 FP5 FP6 FP7 FP8 SEAT6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 Pinouts for Connectors J1-J6 F20 DUT285 F21 DUT286 F22 F23 F24 FP5 Reserved FP6 FP7 FP8