Star Manufacturing LC-4522 Switch 6 Quiet mode, Switch 7 Not Used, Switches 1,2 Print mode

Page 35

disabled (ON), the computer must send both a line feed code and a carriage return code at the end of each line. Most applications do this automatically.

32 Using the EDS Mode

Note the following check points when trying to figure out which setting to use here: 3 If you find that your ou tput is double-spaced when it should not be, turn

this switch ON (Disabled).

3 If you find that lines are printing over each other, turn this switch OFF (Enabled).

Switch 6: Quiet mode

When the Quiet Mode is enabled (OFF), the printer prints with less noi se than normal printing. Though the Quiet Mode prints more quietly, it also takes considerably longer than normal printing.

Switch 7: Not Used

BANK B

Switches 1,2: Print mode

Turn these switches on or off to select the print mode you want to use.

ON, O N	:LQ mode
ON, OFF	:HS-LQ mode
OFF,ON	:Draft mode
OFF,OFF	:HS-Draft mode

Switches 3, 4, 5: Print Pitch

Turn these switches on or off to form the pattern that matches the print pitch

setting you want to make.
ON, ON, ON :10cpi	OFF,ON, ON	:20cpi
ON, ON, OFF :12cpi	OFF,ON, OFF	:Proportional
ON, OFF,ON :15cpi	OFF,OFF,ON	:10cpi
ON, OFF,OFF :17cpi	OFF,OFF,OFF :10cpi

Switch 6: LQ Font Selection

Selects Roman (ON) or Sanserif (OFF) font to use for LQ printing.

Image 35

Contents LC-4522 Contents Using the EDS Mode Choosing a place for the printer Printer SetupUnpacking the printer Printer SetupGeneral guide General guideRemoving the protective materials Opening the front coverRemoving the protective m aterials Installing the ribbon cassette Installing the platen knobInstalling the ribbon cassette Removing the ribbon cassette Installing the paper guide Installing the paper guideStanding up the paper guide Connecting to a power outlet and turning power on and off Connecting to a power outlet and turning power on and offLoading fanfold paper Loading fanfold paper Printer Setup Loading fanfold paper Printing on fanfold paper Parking fanfold paper Parking fanfold paperUnparking fanfold paper Connecting to your computer Using the tear-off functionPage Control Panel Operations Switching between on-line and off-lineSelecting a font Entering the Print Quality Lock ModeSelecting a Print Quality Entering the Multi-part Mode Micro feed Line feedPaper eject cut-sheet paper Form feed fanfold paperTear-off function fanfold paper Setting the top of form positionSelecting the Quiet Print Mode Changing the auto load position Changing the auto load positionClearing the printer’s buffer Saving a macroInitializing the printer Initializing the printerUsing the EDS Mode About EDS Mode settingsEntering the EDS Mode Selecting a bank Changing a switch settingSelecting a switch Selecting a bankExiting the EDS Mode Printing the current switch settingsEDS Mode Settings EDS Mode SettingsSwitches 3, 4, 5 Print Pitch Switch 6 Quiet modeSwitch 7 Not Used Switches 1,2 Print modeSwitch 5 FF command selection Friction mode only Switches 1,2 Multi-Part ModeSwitch 3 Auto Tear off Long Switch 4 Skip over perforation Tractor mode onlySwitches 4,5 Reserved Switch 6 Print Width Switch 1 Character TableSwitch 2 Character Set Switch 3 Zero StyleSwitches 1,2,3,4 Page Length Tractor Mode Switches 1,2,3,4 Page Length Friction ModeSwitch 5 Top Margin Switches 6,7 Not UsedSwitch 4 Paper Out Detector Switch 1 CR Centering at topSwitch 2 CR Centering at seem line Tractor mode only Switch 3 CR Centering PositionSwitch 5 Strobe timing Switch 5 BuzzerSwitch 6 Print direction command Switches 1, 2, 3, 4 International Character SetSwitches 1, 2, 3, 4, 5 Code Switch 6 Saving Control Panel Status Setting up for printing with MS-DOS Setting up for printing with MS-DOSCut-Sheet Paper with Optional Automatic Sheet Feeder Selecting paper typesPaper Handling Cut-Sheet Paper Manual FeedLabels Fanfold PaperAdjusting for paper thickness Adjusting for paper thicknessManual sheet feeding Automatic fanfold feedingClearing paper jams Clearing paper jams