Tandberg Data T40 manual System Power-on

Page 26

Figure 12. StorageLibrary Cabling (Fibre Channel)

1.Install the library in a rack or install the tabletop kit.

2.Connect the fibre cables to the tape drive.

a. Attach one end of the fibre cable to the fibre port on each tape drive. a. Attach the other end of the cable to the host, switch or hub.

The fibre cable can be connected from the tape drive to a switch rather than a

Note host.

3.Connect your Ethernet cable to the Ethernet port on the rear of the library for remote access to the library via the remote management interface. Push the cable into it snaps into place. Connect the other end to a normal 10/100 BaseT Ethernet outlet.

4.Connect a power cord to the outlet on the power supply on the rear of the library.

5.Power on the library by turning on the rear power switch.

6.Power up the host system.

7.Verify communication with all devices on the bus.

8.Configure your library using the commands on the front panel. For configuration information, refer to Configuring the Library.

System Power-on

At power-on, for the first few seconds the unit performs a sequence of diagnostic tests called Power- On Self Tests (POST). POST also includes a loop-back test of the robotics cabling.

After the POST sequence completes successfully, the library will respond to SCSI selections. Then the system starts a series of initialization functions, a process that consists of robot calibration operation and cartridge inventory of magazines and drive. The barcode labels on the cartridges will be read when running inventory.

During these operations, the library continuously shows the map status on the screen. The status of all magazine slots and the drives are initially unknown, and a question mark (?) is displayed for each slot. As the robot searches the magazine slots for cartridges during inventory, the display is updated.

The tape drive needs up to 60 seconds after power-on until it is active on the

Note SCSI bus. You should turn on the power at least 60 seconds before the computer system is started.

18

Installing the Library

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Installation and User Guide Copyright 2006 Tandberg Data ASA Table of Contents Information about the Operator Interfaces Updating Firmware Approved Drive Types Figures Tables Waste Electrical and Electronic Equipment Directive Explanation of Symbols and NotesAbout This Guide Product Model NumberOther Documents You Might Need Getting More Information or HelpTape Drive Support Product OverviewProduct Description Front Panel Data Transfer RatesMagazines Rear Panel LED IndicatorsStandby Switch Control ButtonsADI Bridging and LUN Library FeaturesOperator Interfaces Station PartitionsControl Path Simple Network Management Protocol SnmpBrowser Requirements Unpack Unpacking the StorageLibraryFinding a Location for the StorageLibrary Page Installing the Library Remove the Transport Locking ScrewsMounting the StorageLibrary in a Rack Mounting the Rack mount Ears Rack mounting Kit with Rack mount Ears Right figureInstalling the Right Rail Assembly Installing the Rails in a RackInstalling the Left Rail Assembly Mounting the StorageLibrary to the Rack StepInstalling the Library Connecting Library Cables ScsiConnecting the Cables Connecting Library Cables Fibre ChannelGuidelines for Connecting the Scsi Cables System Power-on Labeling Cartridges for the Barcode Reader Page Scroll Function Information about the Operator InterfacesFront Panel Interface FPI Remote Management Interface Menu TreesPage Network Operations Assign Media Import Media Setup Setup WizardTools Prepare to Ship Restore Default Reports LibraryReports Network Operations Export Media Setup SlotsDrive FW Upgrade System Test Cycle test Reset Web Password License Key RAS Tickets StatisticsPage Diagnostics Operations Assign Media Setup Setup WizardTools Maintenance Import Media NetworkRAS Tickets Statistics License Key Notification Web Password Reports NetworkHome Screen ToolsOperator Privileges RMI Home ScreenWords Commonly Used on the FPI and RMI Symbol on FPI DescriptionSymbol Description WordMap Menu Status Page Using the Default Administrative User Account Administrator Configuring the LibraryAbout the Setup Wizard Using the Setup Wizard Setup Wizard TasksConfiguring Network Settings Remote Access Applying a License KeyFrom the FPI, select Setup Activate License Configuring I/E SlotsConfiguring Cleaning Slots Creating Partitions Configuring PartitionsFrom the RMI, select Setup Partition/Drive Reconfigure Partitions Changing Partition ModesSetting Drive ID Modifying the Control PathConfiguring Autoclean Configuring FPI PasswordSetting Date and Time Configuring RMI PasswordConfiguring Menu Timeout Configuring Barcode ScanConfiguring E-mail Notification Configuring Audible AlarmConfiguring Snmp Page Logging Out Running the LibraryLogging Importing CartridgesImporting Cartridges via I/E Slot Unloading from Tape Drives Exporting CartridgesLoading to Tape Drives Import Cartridges via Bulk Loading of MagazinesCleaning Media Handling Cleaning Tape DrivesImporting Cleaning Media Exporting Cleaning MediaMagazine Handling Manual CleanTaking the Library Online/Offline Taking a Library OnlineRemoving Cartridges from the Magazine Removing the Magazine from the UnitInserting Cartridges into the Magazine Inserting a Magazine into the Unit Manual/Emergency Release of MagazinesStandby Functionality Getting Status and Information Viewing Library SettingsViewing Partitions/Drive Settings Viewing Network Settings Viewing StatisticsViewing Log Page Adding, Removing and Replacing Power Supply UnitRemoving and Replacing a Power Supply Required tools NoneRequired tools Screwdriver Tape Drive UnitAdding a Tape Drive Permanently Removing a Tape Drive Removing and Replacing a Tape DrivePage Updating Firmware Updating Library FirmwareFrom the RMI, select Tools Drive Settings Updating Drive FirmwareFrom the FPI, select Tools Drive Settings Page Working With Cartridges and Barcodes Handling Cartridges ProperlyBarcode Requirements Installing Barcode LabelsWrite-Protecting Cartridges Viewing RAS Tickets TroubleshootingAbout RAS Tickets Supported RAS Tickets Parameters and Priority Closing RAS TicketsSupported RAS Tickets Display Message Description Ticket Suggested ActionDisplay Message Interpreting LEDs Verifying Hardware Maintenance MenusDiagnostics Menu Item nameVerifying Recent Changes Troubleshooting MatrixSoftware Checking Problem Power Solution Problem Cartridge Movement Problem Media Problem Scsi problemsProblem Library Performance Problem CleaningProblem Solution Errors Displayed on Front Panel Problem Write or Read IssuesProblem LED Error Messages Problem Remote Management Problem Forgot PasswordShipping or Transporting StorageLibrary Reinserting the Transport Locking ScrewsPacking the StorageLibrary Transport Locking Screws Marked with Red Plastic TabSpecifications T40 Library 4U control moduleDimensions Library DimensionsLibrary Component Weights WeightPower Requirements Climatic SpecificationsPage EMC Approvals Safety and Regulatory InformationSafety Approvals EuropeCanada Conformity DeclarationsJapan Australia/New ZealandApproved Drive Types
Related manuals
Manual 5 pages 53.87 Kb

T40 specifications

Tandberg Data T40 represents a significant advancement in data storage technology, offering users a robust and reliable solution for managing and preserving their information. This external tape drive is designed for small to medium-sized businesses that require high-capacity backup and archiving options. The T40 seamlessly combines efficiency with cutting-edge technology, making it a favored choice among IT professionals.

One of the standout features of the Tandberg Data T40 is its native capacity, which supports 1.5TB of storage per cartridge. With data compression, this capacity can effectively double, allowing for up to 3TB of data to be backed up in a single cartridge. This high capacity minimizes the number of tapes needed for extensive data storage, streamlining the backup process.

The T40 utilizes LTO technology, specifically LTO-5, LTO-6, or LTO-7, depending on the model. LTO, or Linear Tape-Open, is known for its high performance and reliability, offering fast data transfer rates. The T40 can achieve transfer speeds of up to 140MB/s, significantly reducing backup windows and enhancing overall productivity. Its backward compatibility ensures that users can access data stored on previous LTO generations, providing additional flexibility and security for businesses transitioning to newer technologies.

Additionally, the T40 features a simple, user-friendly interface that facilitates easy operation and maintenance. Equipped with a built-in LCD display, users can easily monitor the status of the tape drive, eliminating unnecessary guesswork. The drive's design supports extensive connectivity options, including USB 3.0 and SAS interfaces, making it compatible with various systems and infrastructure setups.

The Tandberg Data T40 is also designed with durability in mind. Its robust construction includes features that protect against dust and other environmental factors, ensuring the longevity of the device. Furthermore, its energy-efficient design helps reduce operational costs, making it an economical choice for budget-conscious organizations.

In summary, the Tandberg Data T40 is a powerful external tape drive that combines high capacity, fast performance, and reliability. Its LTO technology, ease of use, and durability make it an invaluable asset for businesses looking to safeguard their critical data while maximizing storage efficiency. Whether for backup or archiving needs, the T40 stands out as a versatile and dependable solution in the data storage landscape.
Top Page Image Contents