Worth Data RF Laser user manual Channel, Code 3 of 9 Code

Page 13

RF Laser Setup Parameters

Channel

Default Channel

0

•The default Channel is always shipped as 0. There are 10 channels in the USA and Canada. The Channel for the RF Laser Reader is set by scanning the Setup Menu.

•All Lasers and associated Base Station must be set to the same channel. If you have more than one RF Laser per Base Station, you must set a unique ID in each RF Laser. (See SET ID.)

•The Laser channel must match the channel on the Base station. See Appendix A for information on changing the channel on the Base from the shipped default channel of 0.

Code 3 of 9 (Code 39)

Enable Code 39	0
Disable Code 39	1
Enable Full ASCII Code 39	2
Disable Full ASCII Code 39	3
Enable Code 39 Accumulate Mode	4
Disable Code 39 Accumulate Mode	5
Enable Start/stop character transmission	6
Disable Start/Stop character transmission	7
Enable Mod 43 Check Digit	8
Disable Mod 43 Check Digit	9
Enable Check Digit Transmission	A
Disable Check Digit Transmission	B
Caps Lock ON	C
Caps Lock OFF	D

For information about Code 39 and Full ASCII Code 39, see Appendix C. See page 23 for information about Accumulate Mode (this setting also controls Code 93 and Code 128).

Enabling Start/Stop character transmission means that the RF Laser Reader will transmit the * Start/Stop characters to your computer along with the data. For example, data of 1234 would be transmitted as *1234*.

Enabling the Mod 43 Check Digit requires the units position of your data to match the calculation for the check digit explained in Appendix C.

10

Image 13

Contents Worth Data Inc August Page Table Of Contents Introduction Components of RF Laser Readers InstallationScanner Beeps and LEDs what they mean USB Installation Installing the R/F Reader with a dedicated serial port Menu Installing the R/F Reader between a computer and terminalF34, DB25 Null Modem Cable Laser Serial Model Pin-outsF36, DB9 Straight Cable Pin-outs ModUPC\EAN Laser Scanning Instructions Using The RF Laser Setup Menu Code 3 of 9 Code ChannelUPC/EAN Code MSI and Plessey Disable MSICodabar 5 CodeBeep Options 5 Data LengthPreamble Bar Code Data Preamble Data Transmitted 123 PostambleXYZ123 12345678Set ID Character CharactersLink Test Code Scan Start Setup Scan Aiming Dot Duration ResetScan End Setup Scan Start Setup Scan 2Scan Start Setup Scan 2 of 5 Code Scan Start Setup Scan TerminatorScan Start Setup Scan Code Data bits Baud rateParity Stop bitsTest the RF Laser with your computer Page Operational Details Radio ConsiderationsRange Accumulate Mode PC Key Full Ascii Menu Bar Code Function/Control Key SupportFunction keys F11 and F12 Command and Option Keys on Mac USB KeyboardsWindows Key Full Ascii MenuAll Models Troubleshooting TroubleshootingReader wont beep when reading bar codes Poor read rateWindows XP USB Trouble ShootingReader doesnt beep when you try to read your bar codes Serial TroubleshootingData characters are garbled or missing Changing Jumpers and Channels Page Recharging the Batteries American National Standards Institute Customer Service Specifications for Code+ 2 + 3 + 33 + 34 + 35 = Table C-1. Mod 43 Check character calculation for Code108/43 = 2 with a Remainder Value 22 is the Check CharacterTable C-2. Full Ascii Table Full Ascii Extension to CodeCode 93 Specifications A12345b Codabar SpecificationsUCC-128/ EAN-128 Code 128 SpecificationsGS1 US Interleaved 2 of 5 Mod 10 check digit calculation Interleaved 2 of 5 Code019873 60 57 =UPC Specifications UPC 2 and 5-character supplemental codes Isbn Specifications+ 9 +8 + 4 + 3 + 1 = 1831458993833 x 3 = + 9 + 5 + 1 + 8 =01234500006 123450000601234565 MSI/Plessey Specifications 4,5,6,7,2,3,4,5,6,7 943457842+ 12 + 32 + 35 + 30 + 28 + 6 + 12 + 36 = 195/11 = 17 remainderRF Laser Setup RF Laser Setup MenuLink Test Code 5 Code Code 35 Length RSS-14SET Clear CodeStart Setup for Base only RF Base Station Setup MenuFull Ascii Menu 056 057 058 059 060 061 062 063 064 065 066 067 +X* *+Y* *+Z* *%P +T* *+U* *+V* *+W%R* *%S* *%T 33, 37, 38, 39, 43 IndexSee Appendix J UPC/EAN