Worth Data Installation, Components of RF Laser Readers, Scanner Beeps and LEDs what they mean

Page 5

Installation

Components of RF Laser Readers

In the event the shipping box shows damage on arrival, please note the damage on the carrier's receipt log.

The supposed contents of your Reader shipment is the following:

1.An B78 RF Base Station with 1-10 LZ400-RF Lasers.

2.A Worth Data regulated 5V power supply with each LZ400-RF Laser Scanner ordered, and if you ordered a serial cable with the B78 Base Station, you will receive a power supply for the Base also. TO

PREVENT DAMAGING the Base Station or RF Laser, DON'T USE ANY OTHER BRAND OF POWER SUPPLIES.

3.Either a serial cable (F36) or USB cable (C21), depending on which one you ordered.

4.A plastic barpad for entering variable quantity information and performing the Link Test without data transmission.

Scanner Beeps and LEDs (what they mean)

When you scan, you will get one beep when you get a successful decode and a high-pitched beep. The data is then transmitted to the Base Station (as it is being transmitted, the LED flashes yellow). When the Laser receives the acknowledgement from the Base Station that the data has been received, the Laser emits a lower pitched beep and turns on a green LED for three seconds.

If the transmitted data fails to be acknowledged,

1)further scanning is prohibited. You can't pull the trigger again until the data reaches the base or until you clear the scanner.

2)The laser will retransmit three times, (the yellow LED will indicate retransmissions).

3)If it fails three times, it will emit a distinct 8 beep pattern and turn off. This is your clue to check out the Base Station.

4)You can pull the trigger to try transmission again. (the laser beam will not come on until the transmission is acknowledged or you hold the trigger down for 30 seconds to clear the data).

2

Image 5

Contents Worth Data Inc August Page Table Of Contents Introduction Scanner Beeps and LEDs what they mean InstallationComponents of RF Laser Readers USB Installation Installing the R/F Reader with a dedicated serial port Menu Installing the R/F Reader between a computer and terminalF34, DB25 Null Modem Cable Laser Serial Model Pin-outsF36, DB9 Straight Cable Pin-outs ModUPC\EAN Laser Scanning Instructions Using The RF Laser Setup Menu Code 3 of 9 Code ChannelUPC/EAN Code MSI and Plessey Disable MSICodabar 5 CodePreamble 5 Data LengthBeep Options Bar Code Data Preamble Data Transmitted 123 PostambleXYZ123 12345678Link Test Code CharactersSet ID Character Scan Start Setup Scan Aiming Dot Duration ResetScan End Setup Scan Start Setup Scan 2Scan Start Setup Scan Code Scan Start Setup Scan TerminatorScan Start Setup Scan 2 of 5 Code Data bits Baud rateParity Stop bitsTest the RF Laser with your computer Page Range Radio ConsiderationsOperational Details Accumulate Mode PC Key Full Ascii Menu Bar Code Function/Control Key SupportFunction keys F11 and F12 Command and Option Keys on Mac USB KeyboardsWindows Key Full Ascii MenuAll Models Troubleshooting TroubleshootingReader wont beep when reading bar codes Poor read rateWindows XP USB Trouble ShootingReader doesnt beep when you try to read your bar codes Serial TroubleshootingData characters are garbled or missing Changing Jumpers and Channels Page Recharging the Batteries American National Standards Institute Customer Service Specifications for Code+ 2 + 3 + 33 + 34 + 35 = Table C-1. Mod 43 Check character calculation for Code108/43 = 2 with a Remainder Value 22 is the Check CharacterTable C-2. Full Ascii Table Full Ascii Extension to CodeCode 93 Specifications A12345b Codabar SpecificationsUCC-128/ EAN-128 Code 128 SpecificationsGS1 US Interleaved 2 of 5 Mod 10 check digit calculation Interleaved 2 of 5 Code019873 60 57 =UPC Specifications UPC 2 and 5-character supplemental codes Isbn Specifications+ 9 +8 + 4 + 3 + 1 = 1831458993833 x 3 = + 9 + 5 + 1 + 8 =01234565 123450000601234500006 MSI/Plessey Specifications 4,5,6,7,2,3,4,5,6,7 943457842+ 12 + 32 + 35 + 30 + 28 + 6 + 12 + 36 = 195/11 = 17 remainderLink Test Code RF Laser Setup MenuRF Laser Setup 5 Code Code 35 Length RSS-14SET Clear CodeStart Setup for Base only RF Base Station Setup MenuFull Ascii Menu 056 057 058 059 060 061 062 063 064 065 066 067 %R* *%S* *%T +T* *+U* *+V* *+W+X* *+Y* *+Z* *%P 33, 37, 38, 39, 43 IndexSee Appendix J UPC/EAN