Panasonic AJ-LT85P TC Mode, Free, Reg, Ltc, Preset, As&In, Assem, Insrt, TC Jump, Phase Corr, Mon

DETAILED DESCRIPTION OF SET-UP MENUS

TIME CODE

	Item		Setting		V	V
				Description of setting	T	T
No.	Item	No.	Item		R	R
					1	2
507	TC MODE	0000	P-REC	This selects whether the time code generated by the internal TCG or an
		0001	P-FREE	external time code is to be used.
		0002	I-REG	0: Internal TC is set to PRESET and used in the REC RUN mode.
		0003	E-VITC	1: Internal TC is set to PRESET and used in the FREE RUN mode.	ª	ª
		0004	E-LTC	2: Internal TC is used in the REGEN mode.
		0005	VTR1 TC*	3: VITC of input video signals is used in the REGEN mode.
				4: Time code input LTC is used in the REGEN mode.
				5: The time code of the sub-code is used in the REGEN mode when the
				OPERATION MODE switch is in the INT mode.
508	TC			This sets the TCG (time code generator) value.
							Detailed
	PRESET			00:00:00:00 to 23:59:59:29	ª	ª
509	UB			This sets the user bit value.
	PRESET			00 00 00 00 to FF FF FF FF	ª	ª	description
510	REGEN	0003	SW	0: The I-REGEN operation is performed during assemble editing and insert
		0000	AS&IN	Regardless of the set-up menu No. 507 (TC MODE) setting, this sets the
	MODE	0001	ASSEM	I-REGEN mode during assemble editing and/or time code (TC) insert editing
		0002	INSRT	(TC rewrite mode).
				editing.		ª	of
				1: The I-REGEN operation is performed during assemble editing.			set-
				2: The I-REGEN operation is performed during insert editing.
				3: The I-REGEN operation accords with the set-up menu No. 507 (TC MODE)			up
				setting.
							menus
511	TC JUMP	0000	OFF	This sets whether TC JUMP is to be enabled.
		0001	VTR1	0: TC JUMP is disabled.
		0002	VTR2	1: TC JUMP is enabled for VTR1 only.
		0003	ALL	2: TC JUMP is enabled for VTR2 only.		ª
				3: TC JUMP is enabled for both VTR1 and VTR2.
				<Note>
				When TC JUMP is enabled, the tape is first cued up to the IN point and, using
				this IN point as a reference, preroll and the approach are then conducted.
				The TC reference is selected as soon as the IN point is passed and editing
				and recording are initiated.
512	PHASE CORR	0000	OFF	This selects whether the phase compensation of LTC generated by TCG is to
		0001	ON	be controlled.	ª	ª
				0: The phase compensation is not controlled.
				1: The phase compensation is controlled.
513	V-MON/	0000	V-MON	This selects whether the video monitor output connector is to be used as the
	TC OUT	0001	TCOUT1	TC output connector.
		0002	TCOUT2*	When it is used as the TC output connector, align the phase of the TC signal
				which is output in the E-E mode with the phase of the video output or input
				TC signal.
				0: The connector is used as the video monitor output connector.	ª	ª
				1: The connector is used as the TC output connector, and in the E-E mode
				the phase of the TC signal which is output is aligned with the phase of the
				input TC signal.
				2: The connector is used as the TC output connector, and in the E-E mode
				the phase of the TC signal which is output is aligned with the phase of the
				video output signal.

*The VTR1 TC and TCOUT2 settings can be performed only for VTR2.

31