Panasonic AJ-LT85P manual DIAG-MENU Operations, To transfer from a regular mode to the Diag mode

Page 71

DIAG-MENU OPERATIONS

The unit’s system software version display, hour meter displays for the drum motor, rotating heads, etc. (for number of hours used can be viewed on the DIAG menu.

DIAG-MENU HOUR METER <VTR-2>

＊�H00	OPERATION	10000H
H01	DRUM RUN	10000H
H02	TAPE RUN	10000H
H03	THREADING	10000T
H11	DRUM RUN r	10000H
H12	TAPE RUN r	10000H
H13	THREADING r	10000T

DIAG-MENU <VTR-2>

DISPLAY Ver<1.00-00> AV-SYSCON Ver<1.00-00>

SBCVer<1.06-00>

CYLINDER Ver<1.00-00>

REELVer<1.00-00>

END

Hour meter display	Version display
	(Above display is version for
	VTR2.)

To transfer from a regular mode to the DIAG mode:

!Set the unit to the jog mode.

• Remember that the mode cannot be transferred in the shuttle mode.

@Press the DIAG (SHIFT+REC) buttons. (This cannot be done by remote control.) The hour meter displays appear on the VTR1 and VTR2 monitor screens.

#Turn the dial to move to an item.

Turn it clockwise (FWD) to move down and counterclockwise (REV) to move up.

To display the version:

!Press the FF button on the VTR2 while holding down the SHIFT button. The display changes from hour meter to version.

To return from the DIAG mode to the normal mode:

Press the DIAG (SHIFT+REC) buttons.

Diag-menu operations

71

Image 71

Contents Operating Instructions FCC Note For Your SafetyContents Introduction FeaturesLiquid-crystal monitor section Controls and Their FunctionsCounter display section Front Keyboard Switches Level Controls VTR Control Section for both VTR1 and VTR2 Player/Recorder Control SectionEdit Mode Setting Section Automatic Editing Control Section 0AUTO EDIT/MULTI button Button for both VTR1 and VTR2OUT button for both VTR1 and VTR2 PREVIEW/REVIEW buttonTop Section Side Panel Section for both VTR1 and VTR2Front Section Connector Section for both VTR1 and VTR2 Opening Opening and Closing the LaptopUse of Panasonic consumer DV cassette tapes is recommended Compatible TapesAC adaptor System ConnectionsConnections for transmission Microwave transmitter System applications Backup recording using 2 VTRsRecording the same signal on 2VTRs Recording different signals on 2 VTRsEditing controller Switch settingVTR2 Using two VTRs as source units for AB roll editingControl EXT VTR When using an external VTR as the editing source unitControl EXT VTR Play Delay VTR1 External VTR AJ-LT85SET-UP Menu Operations Basic Detailed Description of SET-UP MenusOperation Dial HumidOPE SearchInterface Edit After SynchroEDL Auto CLRTape Protect Time Code Free TC ModePreset Phase CorrVideo Audio PB Fade ST1Output ST2System Preparation of Editing Tape Preview Standard modeBasic Flow of Editing Operations 1st editSplit editing Assemble edit modeInsert edit mode Types of Edit Modes and IllustrationsSearch dial CUT Editing ProcedureEdit mode selection During normal playback press the Still button Edit point registrationTo produce a still picture of the desired scene Edit point checking, revising and clearing To suspend preview and execute automatic editing When preview is executedTo recall the contents of the previous preview Cut editing Editing executionReview Displaying the audio split amount Audio Split Editing ProcedureRevising an edit in point Displaying the video split amount Video Split Editing ProcedureCorrecting an edit in point Still Picture Editing Editing by Edit in Point Setting onlyWhen executing editing without preview Track Function Auto TAG EditingTC Jump Function Registering events How to register eventsWhen 00 appears as the event number Event EditingCalling an event Accessing an event prior to the event now displayedAccessing the event ahead of the event now displayed Executing event editing Revising and clearing eventsClearing all the events initializing the EDL Displaying event numbers Calling the previously previewed contentsEdit Data Management EDL N35Dump Edit Data Dumping TO/LOADING from AN External DeviceSteps taken for dumping Steps taken for loadingDCD DTR GND DSR RTS CTS Communications parameter settingsFormat selection common to Dump and Load Reel numbers Audio split editing Reference Concerning the EDL formatEvent numbers Effect type CH1/CH2 CH1 CH2CH2 CH1 VTR Connections with the AJ-YA752 Audio Memory UnitUser bit Time code generator TCG and user bit generator UBG modesTime codes Time Codes TC and User Bits UB Mode other than Auto Edit VTR1 and VTR2 Auto Edit mode VTR2 onlyTurning on the REC Same function Vitc output specificationsTC OUT LTC output specifications REC Same functionSending out the signals Encoder AdjustmentsTo adjust the encoder using the laptop Waveform on WFM Waveform on WFM Waveform on VSCTo adjustment the brightness LIQUID-CRYSTAL TV Monitor AdjustmentsAdjustment in display section Adjustments in set-up menu modeSearch speed display Superimpose Screen DisplaysTo superimpose displays BlockCTL counter display What is displayedCharacters displayed Audio Connector SignalsError No Details of error VTR operation Error MessagesTake-up reel motor speed is abnormally high To display the version To transfer from a regular mode to the Diag modeTo return from the Diag mode to the normal mode DIAG-MENU OperationsDetailed Description of Diag Menu Condensation Video head cleaningMaintenance OthersGeneral Video SpecificationsSpecifications Panasonic Canada Inc