Panasonic AJ-LT85P manual Edit point checking, revising and clearing

Page 41

CUT EDITING PROCEDURE

Edit point checking, revising and clearing

To check the edit points:

Press the IN or OUT button of the VTR on whose tape the edit points are to be checked. The registered edit point now appears on the counter display.

To check the edit point image:

Press together the IN or OUT button and GO TO button of the VTR on whose tape the image of the edit points is to be checked. The VTR accesses the registered edit point, and its image appears on the monitor.

• If the VTR does not access the edit point, it means that the edit point has not been registered.

To check the total time:

To check the total time of each edit, press the IN and OUT buttons together. The edit time now appears on the counter. To check the total time of the entire editing, press the TOTAL button.

The total time is displayed while this button is held down.

To revise an edit point in 1-frame increments

Press the “+” or “–” button while holding down the IN or OUT button.

The “+” button increases the registered edit point in 1-frame increments.

The “–” button decreases the registered edit point in 1-frame increments.

To clear an edit point

Press the corresponding RESET button while holding down the IN or OUT button of the edit point which is to be cleared.

Cut editing procedure

41

Image 41
Contents Operating Instructions FCC Note For Your SafetyContents Introduction FeaturesLiquid-crystal monitor section Controls and Their FunctionsCounter display section Front Keyboard Switches Level Controls VTR Control Section for both VTR1 and VTR2 Player/Recorder Control SectionEdit Mode Setting Section Automatic Editing Control Section OUT button for both VTR1 and VTR2 Button for both VTR1 and VTR2PREVIEW/REVIEW button 0AUTO EDIT/MULTI buttonTop Section Side Panel Section for both VTR1 and VTR2Front Section Connector Section for both VTR1 and VTR2 Opening Opening and Closing the LaptopUse of Panasonic consumer DV cassette tapes is recommended Compatible TapesAC adaptor System ConnectionsConnections for transmission Microwave transmitter Recording the same signal on 2VTRs Backup recording using 2 VTRsRecording different signals on 2 VTRs System applicationsEditing controller Switch settingVTR2 Using two VTRs as source units for AB roll editingControl EXT VTR Play Delay VTR1 When using an external VTR as the editing source unitExternal VTR AJ-LT85 Control EXT VTRSET-UP Menu Operations Basic Detailed Description of SET-UP MenusOperation OPE HumidSearch DialInterface Edit EDL Auto SynchroCLR AfterTape Protect Time Code Preset TC ModePhase Corr FreeVideo Audio Output ST1ST2 PB FadeSystem Preparation of Editing Tape Basic Flow of Editing Operations Standard mode1st edit PreviewInsert edit mode Assemble edit modeTypes of Edit Modes and Illustrations Split editingSearch dial CUT Editing ProcedureEdit mode selection During normal playback press the Still button Edit point registrationTo produce a still picture of the desired scene Edit point checking, revising and clearing To suspend preview and execute automatic editing When preview is executedTo recall the contents of the previous preview Cut editing Editing executionReview Displaying the audio split amount Audio Split Editing ProcedureRevising an edit in point Displaying the video split amount Video Split Editing ProcedureCorrecting an edit in point Still Picture Editing Editing by Edit in Point Setting onlyWhen executing editing without preview Track Function Auto TAG EditingTC Jump Function When 00 appears as the event number How to register eventsEvent Editing Registering eventsCalling an event Accessing an event prior to the event now displayedAccessing the event ahead of the event now displayed Executing event editing Revising and clearing eventsClearing all the events initializing the EDL Edit Data Management EDL Calling the previously previewed contentsN35 Displaying event numbersSteps taken for dumping Edit Data Dumping TO/LOADING from AN External DeviceSteps taken for loading DumpDCD DTR GND DSR RTS CTS Communications parameter settingsFormat selection common to Dump and Load Reel numbers Audio split editing Reference Concerning the EDL formatEvent numbers Effect type CH1/CH2 CH1 CH2CH2 CH1 VTR Connections with the AJ-YA752 Audio Memory UnitUser bit Time code generator TCG and user bit generator UBG modesTime codes Time Codes TC and User Bits UB Mode other than Auto Edit VTR1 and VTR2 Auto Edit mode VTR2 onlyTC OUT LTC output specifications Vitc output specificationsREC Same function Turning on the REC Same functionSending out the signals Encoder AdjustmentsTo adjust the encoder using the laptop Waveform on WFM Waveform on WFM Waveform on VSCAdjustment in display section LIQUID-CRYSTAL TV Monitor AdjustmentsAdjustments in set-up menu mode To adjustment the brightnessTo superimpose displays Superimpose Screen DisplaysBlock Search speed displayCTL counter display What is displayedCharacters displayed Audio Connector SignalsError No Details of error VTR operation Error MessagesTake-up reel motor speed is abnormally high To return from the Diag mode to the normal mode To transfer from a regular mode to the Diag modeDIAG-MENU Operations To display the versionDetailed Description of Diag Menu Maintenance Video head cleaningOthers CondensationGeneral Video SpecificationsSpecifications Panasonic Canada Inc