Panasonic AJ-LT85P manual Counter display section

Page 6

CONTROLS AND THEIR FUNCTIONS

1 2 3 5 6 7 8 9 0 q w e r

INPUTSCH CF SERVO DV REF SCH

EDIT REC INH

W

TC UB CTL DF TOTAL REMAIN

dB – –30 –20 –16 –12 –8 –4 0

 

CH 1

CH 2

4

t

y

u

[2] Counter display section

q“Cassette loaded” display

This lights when a cassette has been loaded.

It flashes when STANDBY OFF mode is activated.

wINPUT and SCH lamps

These light when the SCH signal is input from an external source and SCH is in alignment.

• Only INPUT lights when the SCH signal is input and

SCH is not in alignment.

eREF and SCH lamps

These light when the reference signal is input to the REF IN connector and SCH is in alignment.

•Only REF lights when the reference signal is input to the REF IN connector and SCH is not in alignment.

rEDIT REC/REC/REC INH lamps

EDIT REC: This lights when the VTR is in edit recording mode.

REC: This lights when the VTR is in recording mode.

REC INH: This lights when the VTR is in recording inhibit mode.

tCF lamp

This lights when the color frame is locked.

ySERVO lamp

This lights when the servo is locked.

uDV lamp

This lights when a cassette recorded using a consumer-

use DV machine has been loaded.

iW lamp

This lights when the 16:9 wide screen mode has been set.

oTC lamp

This lights when the time code data is displayed.

!0UB lamp

This lights when the user bit is displayed.

!1CTL lamp

This lights when when control signal (CTL) is displayed.

!2DF lamp

This lights in drop frame mode.

!33TOTAL lamp

This lights when the total editing time is displayed.

!4REMAIN lamp

This lights when the remaining tape is displayed.

!5Operation modes

:Appears during normal playback or recording.

:Appears during playback at 0 to 1× normal tape speed.

:Appears during playback at 1× or more times normal tape speed.

:Appears during fast forwarding operations.

:Appears during playback at –1×normal tape speed.

:Appears during playback in the reverse direction at –1×to 0 times normal tape speed.

:Appears during playback in the reverse direction at –1×or more times normal tape speed.

:Appears during rewinding operations.

:Appears during in the pause/still mode

!6Time counter display

Hours Minutes Seconds Frames

A period appears here in the drop frame mode.

A colon appears here

in the non-drop frame mode.

When nothing appears here, the time code cannot be read (no display either).

All the colons are cleared when the user bit is displayed.

!7Audio level meters

•When the EXT CHECK button is pressed, the meter is set to the fine mode, the ▼mark is placed at the refer- ence level (–20 dB), and each scale unit represents a 1 dB increment. The REC level can be adjusted by sup- plying reference level audio signals from an external

source.

▼�

CH 1

CH 2

•When a blank tape or blank part of a tape is played back, fast forwarded or rewound, the meter is set to the tape position display mode so that the current tape trav- el position can be ascertained.

(Example)

←10's digit in percentage figure ...3

←1's digit in percentage figure ...6

↑�

The tape is now traveling past a position which is

36% of the entire length of the tape from its beginning.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operating Instructions For Your Safety FCC NoteContents Features IntroductionControls and Their Functions Liquid-crystal monitor sectionCounter display section Front Keyboard Switches Level Controls Player/Recorder Control Section VTR Control Section for both VTR1 and VTR2Edit Mode Setting Section Automatic Editing Control Section PREVIEW/REVIEW button Button for both VTR1 and VTR2OUT button for both VTR1 and VTR2 0AUTO EDIT/MULTI buttonSide Panel Section for both VTR1 and VTR2 Front SectionTop Section Connector Section for both VTR1 and VTR2 Opening and Closing the Laptop OpeningCompatible Tapes Use of Panasonic consumer DV cassette tapes is recommendedSystem Connections Connections for transmission Microwave transmitterAC adaptor Recording different signals on 2 VTRs Backup recording using 2 VTRsRecording the same signal on 2VTRs System applicationsSwitch setting Editing controllerUsing two VTRs as source units for AB roll editing VTR2External VTR AJ-LT85 When using an external VTR as the editing source unitControl EXT VTR Play Delay VTR1 Control EXT VTRSET-UP Menu Operations Detailed Description of SET-UP Menus BasicOperation Search HumidOPE DialInterface Edit CLR SynchroEDL Auto AfterTape Protect Time Code Phase Corr TC ModePreset FreeVideo Audio ST2 ST1Output PB FadeSystem Preparation of Editing Tape 1st edit Standard modeBasic Flow of Editing Operations PreviewTypes of Edit Modes and Illustrations Assemble edit modeInsert edit mode Split editingCUT Editing Procedure Edit mode selectionSearch dial Edit point registration To produce a still picture of the desired sceneDuring normal playback press the Still button Edit point checking, revising and clearing When preview is executed To recall the contents of the previous previewTo suspend preview and execute automatic editing Editing execution Cut editingReview Audio Split Editing Procedure Revising an edit in pointDisplaying the audio split amount Video Split Editing Procedure Correcting an edit in pointDisplaying the video split amount Editing by Edit in Point Setting only When executing editing without previewStill Picture Editing Auto TAG Editing Track FunctionTC Jump Function Event Editing How to register eventsWhen 00 appears as the event number Registering eventsAccessing an event prior to the event now displayed Accessing the event ahead of the event now displayedCalling an event Revising and clearing events Clearing all the events initializing the EDLExecuting event editing N35 Calling the previously previewed contentsEdit Data Management EDL Displaying event numbersSteps taken for loading Edit Data Dumping TO/LOADING from AN External DeviceSteps taken for dumping DumpCommunications parameter settings Format selection common to Dump and LoadDCD DTR GND DSR RTS CTS Reference Concerning the EDL format Event numbers Effect typeReel numbers Audio split editing CH1 CH2 CH2 CH1CH1/CH2 Connections with the AJ-YA752 Audio Memory Unit VTRTime code generator TCG and user bit generator UBG modes Time codesUser bit Time Codes TC and User Bits UB Auto Edit mode VTR2 only Mode other than Auto Edit VTR1 and VTR2REC Same function Vitc output specificationsTC OUT LTC output specifications Turning on the REC Same functionEncoder Adjustments To adjust the encoder using the laptopSending out the signals Waveform on WFM Waveform on VSC Waveform on WFMAdjustments in set-up menu mode LIQUID-CRYSTAL TV Monitor AdjustmentsAdjustment in display section To adjustment the brightnessBlock Superimpose Screen DisplaysTo superimpose displays Search speed displayWhat is displayed Characters displayedCTL counter display Connector Signals AudioError Messages Error No Details of error VTR operationTake-up reel motor speed is abnormally high DIAG-MENU Operations To transfer from a regular mode to the Diag modeTo return from the Diag mode to the normal mode To display the versionDetailed Description of Diag Menu Others Video head cleaningMaintenance CondensationSpecifications General VideoSpecifications Panasonic Canada Inc
Top Page Image Contents