Panasonic AJ-LT85P manual Error Messages, Error No Details of error VTR operation

Page 69

ERROR MESSAGES

When one of the following message numbers appears on the display, the VTR is set to the auto OFF mode (stop) or its power is forcibly turned off. Turn off the power, and then turn it back on. If the error persists after this, consult your dealer.

Error No.	Details of error	VTR operation

E-11	When the cassette was inserted, the reel motor locked up for about 2.5 seconds or	STOP
	longer. When the cassette is ejected, the VTR is set to the auto OFF mode.

E-21	When the cassette was removed, the front loading motor locked up for about 4	STOP
	seconds. When the cassette moves down again and the motor locks up again	STOP
	even if an attempt is made to remove the cassette, the VTR is set to the auto OFF	STOP
	mode if the cassette has moved down.

E-31	The loading motor locked up for about 4 seconds when the cassette was loaded. If	STOP
	the motor locks up even when the cassette is unloaded and loaded again, the cas-
	sette is ejected. The VTR is set to the auto OFF mode.

E-32	The motor locked up for about 4 seconds when the cassette was unloaded. The	STOP
	VTR is set to the auto OFF mode.

E-41	The FG (rotational speed) signal is not output from the cylinder motor.	STOP

E-42	The PG (phase speed) signal is not output from the cylinder motor.	STOP

E-43	The cylinder motor speed is abnormally high.	STOP

E-44	The cylinder motor speed is abnormally low.	STOP

E-51	The FG (rotational speed) signal is not output from the capstan motor.	STOP

E-52	The capstan motor speed is abnormally high.	STOP

E-53	The capstan motor speed is abnormally low.	STOP

E-61	The supply reel motor has locked up.	STOP		Error
E-61	The supply reel motor has locked up.	STOP
				messages
E-62	The take-up reel motor has locked up.	STOP		messages
E-62	The take-up reel motor has locked up.	STOP

E-63	The supply reel motor speed is abnormally high.	STOP

69

Image 69

Contents Operating Instructions FCC Note For Your SafetyContents Introduction FeaturesLiquid-crystal monitor section Controls and Their FunctionsCounter display section Front Keyboard Switches Level Controls VTR Control Section for both VTR1 and VTR2 Player/Recorder Control SectionEdit Mode Setting Section Automatic Editing Control Section OUT button for both VTR1 and VTR2 Button for both VTR1 and VTR2PREVIEW/REVIEW button 0AUTO EDIT/MULTI buttonSide Panel Section for both VTR1 and VTR2 Front SectionTop Section Connector Section for both VTR1 and VTR2 Opening Opening and Closing the LaptopUse of Panasonic consumer DV cassette tapes is recommended Compatible TapesSystem Connections Connections for transmission Microwave transmitterAC adaptor Recording the same signal on 2VTRs Backup recording using 2 VTRsRecording different signals on 2 VTRs System applicationsEditing controller Switch settingVTR2 Using two VTRs as source units for AB roll editingControl EXT VTR Play Delay VTR1 When using an external VTR as the editing source unitExternal VTR AJ-LT85 Control EXT VTRSET-UP Menu Operations Basic Detailed Description of SET-UP MenusOperation OPE HumidSearch DialInterface Edit EDL Auto SynchroCLR AfterTape Protect Time Code Preset TC ModePhase Corr FreeVideo Audio Output ST1ST2 PB FadeSystem Preparation of Editing Tape Basic Flow of Editing Operations Standard mode1st edit PreviewInsert edit mode Assemble edit modeTypes of Edit Modes and Illustrations Split editingCUT Editing Procedure Edit mode selectionSearch dial Edit point registration To produce a still picture of the desired sceneDuring normal playback press the Still button Edit point checking, revising and clearing When preview is executed To recall the contents of the previous previewTo suspend preview and execute automatic editing Cut editing Editing executionReview Audio Split Editing Procedure Revising an edit in pointDisplaying the audio split amount Video Split Editing Procedure Correcting an edit in pointDisplaying the video split amount Editing by Edit in Point Setting only When executing editing without previewStill Picture Editing Track Function Auto TAG EditingTC Jump Function When 00 appears as the event number How to register eventsEvent Editing Registering eventsAccessing an event prior to the event now displayed Accessing the event ahead of the event now displayedCalling an event Revising and clearing events Clearing all the events initializing the EDLExecuting event editing Edit Data Management EDL Calling the previously previewed contentsN35 Displaying event numbersSteps taken for dumping Edit Data Dumping TO/LOADING from AN External DeviceSteps taken for loading DumpCommunications parameter settings Format selection common to Dump and LoadDCD DTR GND DSR RTS CTS Reference Concerning the EDL format Event numbers Effect typeReel numbers Audio split editing CH1 CH2 CH2 CH1CH1/CH2 VTR Connections with the AJ-YA752 Audio Memory UnitTime code generator TCG and user bit generator UBG modes Time codesUser bit Time Codes TC and User Bits UB Mode other than Auto Edit VTR1 and VTR2 Auto Edit mode VTR2 onlyTC OUT LTC output specifications Vitc output specificationsREC Same function Turning on the REC Same functionEncoder Adjustments To adjust the encoder using the laptopSending out the signals Waveform on WFM Waveform on WFM Waveform on VSCAdjustment in display section LIQUID-CRYSTAL TV Monitor AdjustmentsAdjustments in set-up menu mode To adjustment the brightnessTo superimpose displays Superimpose Screen DisplaysBlock Search speed displayWhat is displayed Characters displayedCTL counter display Audio Connector SignalsError No Details of error VTR operation Error MessagesTake-up reel motor speed is abnormally high To return from the Diag mode to the normal mode To transfer from a regular mode to the Diag modeDIAG-MENU Operations To display the versionDetailed Description of Diag Menu Maintenance Video head cleaningOthers CondensationGeneral Video SpecificationsSpecifications Panasonic Canada Inc