Error Message
D: Dialing Errors
Mode | Error code | Description |
| Countermeasure |
TransmissionG3 | D.0.2 | Receiving line is busy | ▲ | Resend the document. |
|
|
| ||
D.0.7 |
| ▲▲ ▲ |
| |
| D.0.3 | STOP was pressed |
| Resend the document. |
| D.0.6 | The receiving fax number is not regis- |
| Set the correct fax number and then resend the document. |
| tered when using the |
| ||
|
|
|
| |
|
| The receiving party did not answer when |
| Set the correct fax number and then resend the docu- |
|
| using the |
| ment. |
|
|
|
|
|
T: Transmission Errors |
|
| ||
|
|
|
|
|
Mode | Error code | Description |
| Countermeasure |
|
| Wrong number (receiving party answered | ▲Check the correct fax number and resend the docu- | |
|
| and hung up) |
| ment. |
|
|
|
|
|
| T.1.1 | The receiving party answered manually | ▲Check how the receiving party should receive a fax. | |
| and hung up the phone | |||
|
|
|
| |
|
|
|
|
|
|
| The receiving party’s machine is not a G3 | ▲Transmission is not available in this machine. | |
|
| machine | ||
|
|
|
| |
|
|
|
|
|
| T.1.4 | STOP was pressed when transmission start- | ▲Resend the document. | |
| ed (only the auto print journal is displayed) | |||
|
|
|
| |
|
|
|
| |
|
| The line status was bad (especially when | ▲Resend the document. If this error occurs repeatedly, | |
|
| communicating overseas) and the receiv- |
| contact your Muratec dealer. |
| T.2.1 | ing party cut off the line |
|
|
|
| Your machine’s settings do not match | ▲Check the settings on the receiving machine. If the receiv- | |
|
| with the receiving party’s |
| ing party has special settings, ask them to release them. |
Transmission |
|
|
|
|
| Due to a line error, communication is not |
| Resend the document. If this error occurs repeatedly, | |
T.2.3 |
| ▲▲caused the error. | ||
|
| available even at the slowest speed |
| contact your Muratec dealer. |
|
| In a consecutive transmission, the sec- |
| Resend the document starting from the page that |
|
| ond page including the following pages |
| |
|
|
|
| |
G3 |
| caused a read error |
|
|
|
|
| ||
T.3.1 | A document longer than 900 mm was sent | ▲Cut one page within 900 mm in length, and resend. | ||
|
|
|
| |
| Brightness in the lamp is insufficient if | ▲Turn the power switch from OFF to ON and try to | ||
|
| |||
|
|
| make a copy. If the error message does not appear, | |
|
| “Lamp error. Call for service” is displayed |
| |
|
|
| resend the document. If the error message appears | |
|
| after transmission is interrupted |
| |
|
|
| again, contact your Muratec dealer. | |
|
|
|
| |
|
|
|
| |
| T.3.2 | Due to a line error, communication failed | ▲Resend the document. If this error occurs repeatedly, | |
|
|
| contact your Muratec dealer. | |
|
|
|
| |
|
|
|
| |
| T.4.1 | Due to a line error, the receiving party cut | ▲Resend the document. If this error occurs repeatedly, | |
| off the line during document transmission |
| contact your Muratec dealer. | |
|
|
| ||
|
|
|
| |
|
| An image quality error occurred at the | ▲All pages were received but some of them might have | |
| T.4.2 |
| had poor image quality. Ask the receiving party to | |
| receiving party (due to line error) |
| ||
|
|
| check the quality of the document. | |
|
|
|
| |
|
|
|
|
|
| T.4.4 | The line cut off during document trans- | ▲Resend the document. | |
| mission (due to line error) | |||
|
|
|
| |
|
|
|
|
|
Getting Started
COPY
Chapter1
COPY
Chapter2
COPY
Chapter3
FAX
Chapter1
FAX
Chapter2
FAX
Chapter3
FAX
Chapter4
Common Settings
In This
Case...
Appendix
In This Case... ● Maintenance and Troubleshooting | |
|
|