Panasonic AJ-LT85P manual Take-up reel motor speed is abnormally high

Page 70

ERROR MESSAGES

Error No.	Details of error	VTR operation

E-64	The take-up reel motor speed is abnormally high.	STOP

E-65	Abnormal tension has been detected.	STOP

E-66	At the tape start or end, the short FF or REW operation does not stop even after 7	STOP
	or more seconds.

E-67	A check sum error was detected in the serial data communication between the	STOP
	syscon and servo.

E-68	In serial data communication between the syscon and servo, the data was fixed at	STOP
	low or high and the absence of data was detected.

E-69	A communication error was detected in the serial data between the syscon and	STOP
	servo when the power was turned on.

E-70	About an hour has elapsed after the fan motor stopped. The VTR forcibly turns off	Forced POWER OFF
	its power.

E-71	The heat sensor was activated and an abnormally high temperature inside the	Forced POWER OFF
	VTR was detected.

E-72	Trouble in the solenoid drive circuitry was detected.	Forced POWER OFF

E-73	Trouble in the cleaning solenoid drive circuitry was detected.	Forced POWER OFF

E-BA	The input supply voltage dropped below the undercut voltage.	Forced POWER OFF (*)

(*) The counter display flashes to provide a warning.

70

Image 70

Contents Operating Instructions For Your Safety FCC NoteContents Features IntroductionControls and Their Functions Liquid-crystal monitor sectionCounter display section Front Keyboard Switches Level Controls Player/Recorder Control Section VTR Control Section for both VTR1 and VTR2Edit Mode Setting Section Automatic Editing Control Section PREVIEW/REVIEW button Button for both VTR1 and VTR2OUT button for both VTR1 and VTR2 0AUTO EDIT/MULTI buttonFront Section Side Panel Section for both VTR1 and VTR2Top Section Connector Section for both VTR1 and VTR2 Opening and Closing the Laptop OpeningCompatible Tapes Use of Panasonic consumer DV cassette tapes is recommendedConnections for transmission Microwave transmitter System ConnectionsAC adaptor Recording different signals on 2 VTRs Backup recording using 2 VTRsRecording the same signal on 2VTRs System applicationsSwitch setting Editing controllerUsing two VTRs as source units for AB roll editing VTR2External VTR AJ-LT85 When using an external VTR as the editing source unitControl EXT VTR Play Delay VTR1 Control EXT VTRSET-UP Menu Operations Detailed Description of SET-UP Menus BasicOperation Search HumidOPE DialInterface Edit CLR SynchroEDL Auto AfterTape Protect Time Code Phase Corr TC ModePreset FreeVideo Audio ST2 ST1Output PB FadeSystem Preparation of Editing Tape 1st edit Standard modeBasic Flow of Editing Operations PreviewTypes of Edit Modes and Illustrations Assemble edit modeInsert edit mode Split editingEdit mode selection CUT Editing ProcedureSearch dial To produce a still picture of the desired scene Edit point registrationDuring normal playback press the Still button Edit point checking, revising and clearing To recall the contents of the previous preview When preview is executedTo suspend preview and execute automatic editing Editing execution Cut editingReview Revising an edit in point Audio Split Editing ProcedureDisplaying the audio split amount Correcting an edit in point Video Split Editing ProcedureDisplaying the video split amount When executing editing without preview Editing by Edit in Point Setting onlyStill Picture Editing Auto TAG Editing Track FunctionTC Jump Function Event Editing How to register eventsWhen 00 appears as the event number Registering eventsAccessing the event ahead of the event now displayed Accessing an event prior to the event now displayedCalling an event Clearing all the events initializing the EDL Revising and clearing eventsExecuting event editing N35 Calling the previously previewed contentsEdit Data Management EDL Displaying event numbersSteps taken for loading Edit Data Dumping TO/LOADING from AN External DeviceSteps taken for dumping DumpFormat selection common to Dump and Load Communications parameter settingsDCD DTR GND DSR RTS CTS Event numbers Effect type Reference Concerning the EDL formatReel numbers Audio split editing CH2 CH1 CH1 CH2CH1/CH2 Connections with the AJ-YA752 Audio Memory Unit VTRTime codes Time code generator TCG and user bit generator UBG modesUser bit Time Codes TC and User Bits UB Auto Edit mode VTR2 only Mode other than Auto Edit VTR1 and VTR2REC Same function Vitc output specificationsTC OUT LTC output specifications Turning on the REC Same functionTo adjust the encoder using the laptop Encoder AdjustmentsSending out the signals Waveform on WFM Waveform on VSC Waveform on WFMAdjustments in set-up menu mode LIQUID-CRYSTAL TV Monitor AdjustmentsAdjustment in display section To adjustment the brightnessBlock Superimpose Screen DisplaysTo superimpose displays Search speed displayCharacters displayed What is displayedCTL counter display Connector Signals AudioError Messages Error No Details of error VTR operationTake-up reel motor speed is abnormally high DIAG-MENU Operations To transfer from a regular mode to the Diag modeTo return from the Diag mode to the normal mode To display the versionDetailed Description of Diag Menu Others Video head cleaningMaintenance CondensationSpecifications General VideoSpecifications Panasonic Canada Inc