Panasonic PT-D5500UL manual Powering off the projector, Direct power off function

Page 23

TEMP	LAMP1	LAMP2	POWER
			D LP

Powering off the projector

Press the POWER OFF “ ” button.

Select “Execute” with or button and press the ENTER button.

(or press the POWER OFF “ ” button again.)

The projection of the image stops, and the power indicator of the main unit lights up orange. (The cooling fan keeps running.)

Wait until the power indicator of the main unit turns to red (i.e., until the cooling fan stops).

Press the “ ” marked side of the MAIN POWER switch to remove all power from the projector.

Attention • Do not turn the power supply off and then immediately back on again.

Turning on the power supply will not light up the light source lamp if the lamp is in the process of cooling down after turning off the power supply. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently. Turning on the power supply with the lamp in the hot condition may shorten the lamp life.

Note • The projector consumes approximately 10 watts of power even in standby mode after the cooling fan stops. (Power indicator lit in red)

•If you re-power the projector after shutting off the main power inadvertently, the projection lamp may remain unlit. Please turn the power on again after a while.

Direct power off function

The power supplied internally causes the cooling fan to continue operating and cool off the lamp when the power has failed or even after the power cord is disconnected immediately after the power has been turned off.

Note • When the lamp has been cooled by the direct power OFF function, it sometimes

takes longer than usual for the lamp to light up again.

•While the cooling fan is operating, do not place the projector inside a box or bag.

•The operation time of the cooling fan will be less if fewer than 2 minutes have elapsed since the power was turned on.

23

Image 23

Contents Commercial Use PT-D5500ULModel number PT-D5500U/PT-D5500UL Dear Panasonic CustomerPage Contents Precautions with regard to safety Always disconnect all cables before moving the projector Insulate the battery using tape or similar before disposalDo not place liquid containers on top of the projector Do not insert any foreign objects into the projectorDo not use the old lamp unit AccessoriesUse only the Specified battery Do not look into the lens while the projector is being usedPrecautions on handling Name and function of parts Set to Computer When the operation mode selectorStatus LED lights Front and side of the projectorRear view of the main unit Controls on rear panel Side-mounted connection terminals Loading dry cells Using the remote control unitEffective range of remote control operation Operation mode selector switch Setting projector ID number to remote controlUsing the remote control as a PC mouse Using a wired remote control Projection distances InstallationInstallation geometry Projection schemesConnection Setup precautionsDigital Hi-vision video deck Example of connecting with AV productsDVD player Video deck Control PC Control PC DVI port DVI-D Cable Option ET-SCDV03 Example of connecting with PCsPC with How to remove the projection lens How to install the projection lensRoughly adjust the focus of the lens. Refer to Powering up the projectorMaking adjustment and selection Press the l button. on the main unit or the remote controlDirect power off function Powering off the projectorChoose an item and adjust it using buttons How to adjust the lensHow to adjust the lens position to the left or right Press the Shutter button again Automatic adjustment Auto SetupUsing the Freeze function Using the Shutter functionChange the magnification with the D.ZOOM + button Using the digital zoom D.ZOOM + functionPress the D.ZOOM + button of the remote control Languageenglish On-screen menusStructure of menu screens Returning to the previous Menu items settingResetting to the factory default Basic menu operationsAdjusting the picture KHz MHz Signal Scan Color FrequencySubcarrier SystemPosition Adjusting the positionENGLISH, DEUTSCH, FRANÇAIS, Español How to use Advanced MenuYpbpr Option 1 settingsLAMP2 Option 2 settingsDual LAMP1Func RS232CCycle of displayed internal test patterns Setting the passwordChanging the password Setting the textLAN cable Setting the network Connecting a PCSystem requirements Connection exampleExamples of connection Using the serial terminalsPin assignments and signal names Communication conditions Factory settingRemarks Control commandsCable specifications Connecting to a PC Computer Projector DTE specificationsSub 9-pin female external appearance Using the Remote 2 terminalPin assignments and control Lamp monitor Indication of lamp monitorMonitor ReplaceDismantle the air filter Cleaning and replacement of air filterProcedure of cleaning Clean the air filterReplacing the lamp unit Timing of lamp unit replacementHave a Phillips screwdriver ready ahead of time Lamp unit replacement stepsRemove the two screws securing the fan unit Select the lamp which has been replaced with the and buttons Click OK Using Web Browser ControlAccess procedure Basic controlStatus information Detail controlParameter Description Error informationWhen Failed has appeared for an item Mail setup DNS server setup Network configAdjust clock POP server setupNetwork status Password changeNot turn on Symptoms ChecksPower does Remote controlPT-D5500U PT-D5500UL SpecificationsWireless mouse receiver Length of power supply cord CabinetOutside dimensions Remote control Power sourceCompatible Signal List Calculation formulas for projection distance by lens types Projection distances by projection lensUnit mm inch DimensionsTrademark Acknowledgement Trademark acknowledgmentsConcernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer d’objets lourds sur le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur Ne pas mettre d’objets étrangers dans le projecteur’utilisez pas un bloc lampe usagé ’utiliser que la pile indiquéeMise au rebut Nettoyage et maintenancePrécautions pour la manipulation Précautions pour le transportPériode de remplacement de la lampe Remplacement de la lampePréparez un tournevis Phillips à l’avance Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée INIT. Compt Panasonic Canada Inc Technical Support